Other

A vibrating motor will provide tactical feedback on your projects! Easy to connect, power efficient and works directly with Dasduino / Arduino. Now your DIY consoles will be more advanced, or you can give your old joysticks a boost in vibration.

For those who do not want to waste time setting up the amplifier, we have made a module for you! TDA7397 located on this plate is a two-channel power amplifier with 15W per channel (with a peak of 25W!). There is also a potentiometer on the product to adjust the volume directly between channels.

This small water pump is extremely easy to use. Dip it into the water or liquid you want to pump, plug the drain hose and connect it to the power supply. It works at 3V to 6V voltage and is capable of expelling 120L per hour. Great to serve as a small water pump!

• Voltage: 3V – 6V
• Max. liquid ejecting height: 40-110cm
• Flow speed: 120L/h
• Exterior diameter of drain tube: 7.5mm
• Interior diameter of drain tube: 4.7mm
• Pump dimensions: 24mm(diameter), 33mm(height)

This wireless charging receiver is fully compatible with the Qi standard, which means that it will provide a voltage at its output when its coil is close enough to another Qi-compatible coil. It can be one from our offer or any Qi-compatible charger. it gives 5V with a maximum current of 0.5A, and has an integrated protection against excessive temperature.

This Qi-compatible transmitter will wirelessly charge any Qi-compatible device.

A solenoid is a special type of electromagnet on which it is possible to control the position of the shaft using currents.

This device uses MCP47A1 which is a single channel, 6-bit digital to analog converter with I2C compatible serial interface. There’s no integrated EEPROM memory which would allow DAC register and configuration bit values to be saved at powered off.

The electromagnetic padlock allows the door to be locked via a microcontroller or other external system. This particular can hold up to 180kg with its electromagnet, which is an extremely high force and is intended for use in places where high security is required.  When power is supplied, it activates.

It consists of two parts, an electromagnet and a piece of metal. A piece of metal is installed on the door, while an electromagnet is installed on the door jamb. Comes with all necessary mounting screws. It is waterproof and can be used in outdoor conditions.

• Activation voltage: 12V
• Constant activation current: do 500mA
• Force if can hold: 180kg
• Dimensions: 172 x 40 x 21mm
• Waterproof

This water pump is extremely easy to use. Soak it in the water or liquid that you want to pump, add a tube to the drain and connect it to the power supply. You can also immerse the pump in the liquid you want to decant. In that case you don’t need to attach a inlet tube in this case. It operates at 12V and is able to expel 240L of fluid per hour.

• Voltage: 12V
• Max. height fluid can reach: 300cm
• Flow rate: 240L/h
• External diameter of drainage tube: 8mm
• Pump dimensions: 55 x 52 x 41 mm

For the purpose of automation in working with plants, there is an electronic valve for the water (or other liquid?). If you need a way to control some fluid using a microcontroller, here it is! It is actually the electronic solenoid which when activated, the fluid passes through his pipe, and if not – will not. Accepts pipe diameter of1/2 and at the inlet has a filter for all the unwanted particles.

It does not contain the pump or even some additional electronics, so make sure to have an external pump or use faucet water with pressure which is large enough. Systems that have a reservoir at a higher altitude than the valve, or to be exact, that apply the principle of hydrostatic pressure will not work because the pressure will not be large enough.

• Voltage: 12V DC
• For pipes with a diameter of 1 / 2inch

• Dimensions: 78 x 60 mm

Electromagnetic lock allows you to lock the door by a microcontroller or an external system. This one can hold up to 60kg with its electromagnet, which is just enough to when used with doors of the appropriate weight. Ideally, it should be used on smaller doors, windows and drawers. It is activated, that is “locked” when it is supplied current.

It consists of two parts, piece of an electromagnet and the metal. Comes with all necessary screws for installation.

In a buzzer speaker, current is run through a coil of wire that produces a magnetic field. The flexible ferromagnetic disc is attracted to the coil when current is flowing through it and returns to a “rest” position when current is not flowing through the coil. The sound from the buzzer speaker is produced by moving a ferromagnetic disc in a similar way to a cone in a speaker.