Filter
Second filter
Third filter
Fourth filter

Actuators

In this category you can find various actuators suitable for all kinds of DIY projects. Some of them are servo and stepper motors, buzzers, relays, etc.

Showing 25–48 of 93 results

Sort by:
USB Type A female breakout
USB Type A female breakout

The USB Type-A connection is still prevalent. If it’s in the electronic devices everywhere around us, it is only natural that we’d want it in our electronic projects. Adding a USB Type-A connection to your circuit is as easy as pie with this breakout board.

 

The breakout board breaks the GND, D+, D-, and VUSB pins out to the plated through-holes.

 

Dimensions: 22 mm x 22 mm
Connectors: USB Type-A (female)
Mounting holes: 2

USB Type A male breakout
USB Type A male breakout

The USB Type-A connection is still prevalent. If it’s in the electronic devices everywhere around us, it is only natural that we’d want it in our electronic projects. Adding a USB Type-A connection to your circuit is as easy as pie with this breakout board.

 

The breakout board breaks the GND, D+, D-, and VUSB pins out to the plated through-holes.

 

Product usage tips:

Male headers for the pads are added and need to be soldered. The breakout board has two mounting holes for placing it on different surfaces.

Smart LED WS2812B Ring7
Smart LED WS2812B Ring7

WS2812B is an extremely interesting LED that can emit light in red, green or blue – or any combination of these three colors, able to show a total of approximately 16 million different colors. On this board, diodes are arranged in a circle. They are controlled by a single pin with only a few lines of code from Arduino IDE. That’s possible thanks to the integrated controller inside the LED itself!

1-channel relay board
1-channel relay board

Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process, because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t even have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

Out of stock 2-channel relay board
2-channel relay board

Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 2 relays.

 

Out of stock 4-channel relay board
4-channel relay board

Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 4 relays.

Out of stock Relay with 5V coil
Relay with 5V coil

Relay is a device with enables switching greater loads – ones that require more voltage/current. These relays can be found in our relays breakouts. It has NO and NC pins.

 

• Current needed for activation (current of Dasduino): 20mA
• Coil voltage: 5V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A

Out of stock Relay with 12V coil
Relay with 12V coil

The relay 12v coil is a device used to turn (overlapping) large loads – those that require higher voltages or currents. These relays are used on the modules with the relay. There are NO and NC pins.

 

• Current needed for activation: 77mA
• Coil voltage: 12V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A

 

Smart LED WS2812B Stick10
Smart LED WS2812B Stick10

WS2812B is an extremely interesting LED that can emit light in red, green or blue – or any combination of these three colors, able to show a total of approximately 16 million different colors. On this board, diodes are arranged in a line of 10. You can even connect these sticks in a line. They are controlled by a single pin with only a few lines of code from Arduino IDE. That’s possible thanks to the integrated controller inside the LED itself!

 

• Number of LEDs: 10
• Voltage: 5V
LED type: WS2812B
• Current: max 60mA per LED
• Dimensions: 80 x 10 mm

Smart LED WS2812B Pixel
Smart LED WS2812B Pixel

These small LEDs are not just ordinary lights – each is unique because it has a built-in small integrated circuit (IC) that is able to turn on the LED light in 16 million different colors. IC is WS2812 and it uses a single wire that can control thousands of these LEDs. With a little imagination by putting these pixels, you get superior effects with a minimum effort. These lamps are easy to control with Dasduino.

Aluminium platform with two wheels for robotic projects
Aluminium platform with two wheels for robotic projects

An aluminum platform with two mountable rubber wheels, two DC motors and balancing third (middle) wheel. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.

 

Material: aluminium
Type: for two wheels
Motor voltage: 3V – 6V
Contents: two wheels, two DC motors with gearbox, aluminium plate, middle wheel, required screws

DC Motor Driver Dual H-Bridge L298N
DC Motor Driver Dual H-Bridge L298N

H bridge supports an exchange of polarities on its outputs and therefore enables control of motor spins in both directions in a very simple way. It can also direct other devices that for certain usage require the exchange of polarities on their inputs.

 

Dual motor H-bridge DRV8424P driver breakout
Dual motor H-bridge DRV8424P driver breakout

The Dual Motor H-Bridge DRV8424P is a high-performance motor driver module that provides efficient and reliable control for two DC motors or a bipolar stepper motor. It is widely used in robotics, automation, and mechatronics projects where precise motor control is required.

 

This motor driver module is based on the DRV8424P integrated circuit, which features advanced protection and control capabilities. It supports a wide range of motor voltages, typically from 8V to 45V, and can deliver a continuous output current of up to 2.5A per motor channel. With a peak current of up to 4A, it can handle high-demand applications.

 

LCD display 16x2 white/blue
LCD display 16x2 white/blue

LCD display with HD44780 controller enables showing text, symbols, value or anything else that comes from Dasduino/Arduino. It is capable of showing 16 symbols in two lines and therefore can be used in many projects that need to send clearly visible and legible output information.

Addressable RGB LED strip ws2812 30LED/m 5V IP20
Addressable RGB LED strip ws2812 30LED/m 5V IP20

This kind of LED strip is unique because each of its diodes has a built-in IC which is able to turn on an LED in 16 000 000 different colors. IC is WS2812 and can control a thousand of these diodes by using just one wire. With this strip, you can create interesting things with minimum effort. This strip is easily controllable by Dasduino.

 

The whole package comes with 5m of LED strip.

Step-down module with LM2596S
Step-down module with LM2596S

This module lowers the input voltage on the specified output voltage that you adjust through the trimmer on the board. It’s very practical because while changing the input voltage, the output voltage always stays the same. However, the input voltage has to be at least 0.7V higher than the output voltage.

Input voltage is IN+ and IN-, while the output is OUT+ and OUT- . A power supply is able only to bring the voltage down, not up!

 

It does not have a protective diode in case of the wrong polarity, pay attention while connecting!

Laser 650nm(red) 5mW 3V
Laser 650nm(red) 5mW 3V

This little laser is capable of showing a small dot on a great distance. You can use it, for example, in combination with a photoresistor to register when somebody has passed through a certain space.

 

• Wavelength: 650nm (red color)
• Power: 5mW
• Voltage: 3V

Out of stock Step-up module with XL6009
Step-up module with XL6009

Smaller booster (step-up) module. Input voltage is increased to the desired level.

 

• Input voltage: 5-32 V
• Output voltage: 5-35 V (adjustable)
• Input current: (max) 10A
• Efficiency: greater than 94%
• Dimensions: 43mm x 21mm x 14mm

Vibrating motor
Vibrating motor

A vibrating motor will provide tactical feedback on your projects! Easy to connect, power efficient and works directly with Dasduino / Arduino. Now your DIY consoles will be more advanced, or you can give your old joysticks a boost in vibration.

Electromagnetic door lock
Electromagnetic door lock

Electromagnetic lock allows you to lock the door by a microcontroller or an external system. This one can hold up to 60kg with its electromagnet, which is just enough to when used with doors of the appropriate weight. Ideally, it should be used on smaller doors, windows and drawers. It is activated, that is “locked” when it is supplied current.

It consists of two parts, piece of an electromagnet and the metal. Comes with all necessary screws for installation.

2-channel relay board with easyC
2-channel relay board with easyC

Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

 

This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.

TDA7297 2x15W audio amplifier
TDA7297 2x15W audio amplifier

For those who do not want to waste time setting up the amplifier, we have made a module for you! TDA7397 located on this plate is a two-channel power amplifier with 15W per channel (with a peak of 25W!). There is also a potentiometer on the product to adjust the volume directly between channels.

I2C LCD adapter
I2C LCD adapter

This adapter makes connection of LCD to Dasduino (or any other Arduino-compatible board) a breeze! It uses I2C communication which needs only two pins. It can be used and work with all of ours LCDs (16×2, 20×4, 16×4). Use our library and get started in few minutes of work!

It’s even easier with easyC – no soldering is needed!

 

Plastic platform (four wheel) for robotic projects
Plastic platform (four wheel) for robotic projects

Plastic platform with slots for four mountable wheels with four DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.

 

Material: plastic, transparent
Type: for four wheels
Contents: one plastic platform
• Needs to be added: four wheels with DC motors

items per page