Filter
Second filter
Third filter
Fourth filter

Actuators

In this category you can find various actuators suitable for all kinds of DIY projects. Some of them are servo and stepper motors, buzzers, relays, etc.

Showing 49–72 of 93 results

Sort by:
Plastic platform (two wheels) for robotic projects
Plastic platform (two wheels) for robotic projects

Plastic platform with slots for two mountable wheels and two DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.

 

Material: plastic, transparent
Type: for two wheels
Contents: one plastic platform
• Needs to be added: two wheels with DC motors

Aluminium platform with four wheels for robotic projects
Aluminium platform with four wheels for robotic projects

An aluminum platform with four mountable rubber wheels and four DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.

 

Material: aluminium
Type: for four wheels
Motor voltage: 3V – 6V
Contents: four wheels with gearbox, aluminium plates, required screws and standoffs, battery holder

Yellow wheel and motor for robotic projects
Yellow wheel and motor for robotic projects

Wheel for robotic projects (65mm in diameter) with black tires made of rubber. It comes with a DC motor that runs from 3V to 6V, and will roll your every project!

Wheel for robotic projects
Wheel for robotic projects

Wheel for robotic projects (65mm in diameter) with black tires made of rubber. It will roll your every project, but it doesn’t come with a motor.

LCD display 16x2 RGB
LCD display 16x2 RGB

LCD screen with HD44780 controller is able to display text, symbols, values or anything else coming from Dasduino/Arduino. It is capable of displaying 16 characters in 2 lines and is useful in many projects that need to send clearly visible and legible output information.

3.5mm Jack breakout
3.5mm Jack breakout

If you are working with audio and need easy access to all the pins of the 3.5mm connector, this breakout makes it possible. It accepts a male 3.5mm connector, in a 4-pin version, and allows access to all connector pins on the header.

 

Dimensions: 22 mm x 22 mm
Board connector: 3.5mm female, accepts 3.5mm male
Connections: ground, speaker right, speaker left, microphone
Mounting holes: 2

8x8 LED matrix MAX7219
8x8 LED matrix MAX7219

The LED matrix 8×8 is a system of 64 interconnected LEDs that, with the help of the MAX7219 LED driver, light up as programmed, and all of this is located on one board and is truly easy to use. You can use them to show letters or symbols, display text, and the like. It is possible to connect several modules with just a few wires and control several matrices at once.

 

The design of the modules is such that they will look like they are from one piece, even if you stack several of them one after the other. The LEDs on the board are beautiful 0402 very small LEDs and give a very nice effect when lit.

Step-down module MP1584 3A
Step-down module MP1584 3A

This module lowers the input voltage to a specific output voltage which you adjust via a trimmer on the board. It is very practical because by changing the input voltage, the output always remains the same. It converts voltages with high efficiency, significantly higher than standard voltage regulators.

 

• Input Voltage: 4.5V – 28V
• Output Voltage: 0.8V – 20V
• Max. current on the output: 3A
• Efficiency: do 96%
• Dimensions: 22 x 17 x 4 mm
• Current Peak: 4A
• Frequency: 100kHz do 1.5MHz

 

There is no protection diode in case of wrong polarity, be careful when connecting!

Out of stock Step-up module LM2587
Step-up module LM2587

Boost (step up) module. The input voltage increases to the desired one with high efficiency.

 

Input voltage: 3.5 – 30 V
 Output voltage: 4.0 -30 V (adjustable)
• Output current: (max) 5A
Efficency: around 90%, do 94%, depends on input and output voltage
• Dimensions: 52 x 38 x 20 cm

Power supply 12V 1A 12W, 5V 1A 5W
Power supply 12V 1A 12W, 5V 1A 5W

This AC-DC power supply is a simple solution to power your 12V or 5V devices. it is especially practicle for projects where you need both standard voltages. Simply give it AC voltage of 230V from the electrical outlet and it gives you 5V with max 1A and 12V with max 1A.

 

WARNING: with this module you will work with high voltages! Apply all safety measures, be sure to turn off the power before connecting, and then isolate the high voltage part.

 

Small electromagnet
Small electromagnet

This magnet is activated by the current passing through it, making it an small electromagnet. It’s perfect for those who need magnets in their projects. Plus, it’s small enough to easily store away when not in use.

 

 

Mini water pump
Mini water pump

This small water pump is extremely easy to use. Dip it into the water or liquid you want to pump, plug the drain hose and connect it to the power supply. It works at 3V to 6V voltage and is capable of expelling 120L per hour. Great to serve as a small water pump!

• Voltage: 3V – 6V
• Max. liquid ejecting height: 40-110cm
Flow speed: 120L/h
Exterior diameter of drain tube: 7.5mm
• Interior diameter of drain tube: 4.7mm
Pump dimensions: 24mm(diameter), 33mm(height)

Electronic water valve 12V DC
Electronic water valve 12V DC

For the purpose of automation in working with plants, there is an electronic valve for the water (or other liquid?). If you need a way to control some fluid using a microcontroller, here it is! It is actually the electronic solenoid which when activated, the fluid passes through his pipe, and if not – will not. Accepts pipe diameter of1/2 and at the inlet has a filter for all the unwanted particles.

 

It does not contain the pump or even some additional electronics, so make sure to have an external pump or use faucet water with pressure which is large enough. Systems that have a reservoir at a higher altitude than the valve, or to be exact, that apply the principle of hydrostatic pressure will not work because the pressure will not be large enough.

 

• Voltage: 12V DC
• For pipes with a diameter of 1 / 2inch

• Dimensions: 78 x 60 mm

DAC 6-bit 1-channel MCP47A1 breakout
DAC 6-bit 1-channel MCP47A1 breakout

This device uses MCP4725 which is a single channel, 6-bit digital to analog converter with I2C compatible serial interface. There’s no integrated EEPROM memory which would allow DAC register and configuration bit values to be saved at powered off.

Small solenoid 6V
Small solenoid 6V

A solenoid is a special type of electromagnet on which it is possible to control the position of the shaft using currents.

 

LED matrix 8x8 with MAX7219 driver
LED matrix 8x8 with MAX7219 driver

LED matrix 8×8 is a system of 64 mutually connected LED lights which use MAX7219 driver to light the way they are programmed, and all that is on one board and is really simple to use. You can use them for printing letters or symbols, showing texts and similar. It is possible to connect more modules with just a few wires and control with more matrixes at once.

 

Electronic water valve 220V AC
Electronic water valve 220V AC

For the purpose of automation in working with plants, there is an electronic valve for the water (or other liquid?). If you need a way to control some fluid using a microcontroller, here it is! It is actually the electronic solenoid which when activated, the fluid passes through his pipe, and if not – will not. Accepts pipe diameter of1/2 and at the inlet has a filter for all the unwanted particles.

 

It does not contain the pump or even some additional electronics, so make sure to have an external pump or use faucet water with pressure which is large enough. Systems that have a reservoir at a higher altitude than the valve, or to be exact, that apply the principle of hydrostatic pressure will not work because the pressure will not be large enough.

Electromagnetic podlock 180kg
Electromagnetic podlock 180kg

The electromagnetic padlock allows the door to be locked via a microcontroller or other external system. This particular can hold up to 180kg with its electromagnet, which is an extremely high force and is intended for use in places where high security is required.  When power is supplied, it activates.

It consists of two parts, an electromagnet and a piece of metal. A piece of metal is installed on the door, while an electromagnet is installed on the door jamb. Comes with all necessary mounting screws. It is waterproof and can be used in outdoor conditions.

 

Activation voltage: 12V
Constant activation current: do 500mA
Force if can hold: 180kg
Dimensions: 172 x 40 x 21mm
• Waterproof

Qi wireless charger - transmitter
Qi wireless charger - transmitter

This Qi-compatible transmitter will wirelessly charge any Qi-compatible device.

 

Qi wireless charger - receiver
Qi wireless charger - receiver

This wireless charging receiver is fully compatible with the Qi standard, which means that it will provide a voltage at its output when its coil is close enough to another Qi-compatible coil. It can be one from our offer or any Qi-compatible charger. it gives 5V with a maximum current of 0.5A, and has an integrated protection against excessive temperature.

 

Digipot 100k MCP4018 breakout
Digipot 100k MCP4018 breakout

A digital potentiometer is a device identical to a potentiometer, except that instead of a physical rotating part that adjusts the resistance, it uses digital communication. Namely, the resistance of the digital potentiometer is adjusted via I2C communication.

Our module is based on the MCP4018 IC which has a total of 128 steps between 0 and 100k resistance values. This would mean that it is capable of doing resistance steps of approximately 781 ohms. It is controlled via I2C which makes it extremely easy to use.

 

Digipot 10k MCP4018 breakout
Digipot 10k MCP4018 breakout

A digital potentiometer is a device identical to a potentiometer, except that instead of a physical rotating part that adjusts the resistance, it uses digital communication. Namely, the resistance of the digital potentiometer is adjusted via I2C communication.

Our module is based on the MCP4018 IC which has a total of 128 steps between 0 and 10k resistance values. This would mean that it is capable of doing resistance steps of approximately 78ohms. It is controlled via I2C which makes it extremely easy to use.

Digipot 50k MCP4018 breakout
Digipot 50k MCP4018 breakout

A digital potentiometer is a device identical to a potentiometer, except that instead of a physical rotating part that adjusts the resistance, it uses digital communication. Namely, the resistance of the digital potentiometer is adjusted via I2C communication.

Our module is based on the MCP4018 IC which has a total of 128 steps between 0 and 50k resistance values. This would mean that it is capable of doing resistance steps of approximately 390ohms. It is controlled via I2C which makes it extremely easy to use.

Digipot 5k MCP4018 breakout
Digipot 5k MCP4018 breakout

A digital potentiometer is a device identical to a potentiometer, except that instead of a physical rotating part that adjusts the resistance, it uses digital communication. Namely, the resistance of the digital potentiometer is adjusted via I2C communication.

Our module is based on the MCP4018 IC which has a total of 128 steps between 0 and 5k resistance values. This would mean that it is capable of doing resistance steps of approximately 39ohms. It is controlled via I2C which makes it extremely easy to use.

items per page