In this category you can find various actuators suitable for all kinds of DIY projects. Some of them are servo and stepper motors, buzzers, relays, etc.
Showing 49–72 of 86 results
Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.
This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.
Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process, because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t even have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.
Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 2 relays.
Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 4 relays.
Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.
This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.
The USB Type-C is ubiquitous. We always wanted to add it to our electronics projects, and we’re sure you did too. Adding a USB Type-C connector to your projects is easier than ever thanks to this USB Type-C breakout board. It will allow you to send data to your device, as well as add power to the circuit.
The USB Type-C connector’s GND, CC2, SBU2, D-, D+, SBU1, CC1, and VUSB pins are broken out to the plated through-holes.
Product usage tips:
Male headers that are included need to be soldered to the board. The breakout board has two mounting holes and can be placed on any surface.
The MicroUSB is still everywhere around us, even though it’s slowly being replaced with USB Type-C. We’re sure you wanted to add it to your electronics projects. We did, too, that’s why we added the MicroUSB female connector breakout board to our roster!
The Micro B USB connector’s GND, ID, D+, D-, and VCC pins are broken out to the plated through-holes.
Product usage tips:
The pins included need to be soldered to the board. It won’t move an inch when mounted with the two mounting holes.
This adapter makes connection of LCD to Dasduino (or any other Arduino-compatible board) a breeze! It uses I2C communication which needs only two pins. It can be used and work with all of ours LCDs (16×2, 20×4, 16×4). Use our library and get started in few minutes of work!
It’s even easier with easyC – no soldering is needed!
The stepper motor driver enables very precise control of the stepper motor. The DRV8825, located on this board, enables microstepping of a bipolar motor with an adjustable current limit, overcurrent and overtemperature protection. Controls steps up to 1/32 step. It has a potentiometer for setting the desired current.
• Voltage: 8.2V – 45V
• Current: 1.5A per phase without heatsink, 2.2A per phase with heatsink
• Dimensions: 38 x 22mm
We all know these little DC motors, especially if you’ve ever disassembled any toy. They are everywhere, and now at the Soldered.com.
The electromagnetic padlock allows the door to be locked via a microcontroller or other external system. This particular can hold up to 180kg with its electromagnet, which is an extremely high force and is intended for use in places where high security is required. When power is supplied, it activates.
It consists of two parts, an electromagnet and a piece of metal. A piece of metal is installed on the door, while an electromagnet is installed on the door jamb. Comes with all necessary mounting screws. It is waterproof and can be used in outdoor conditions.
• Activation voltage: 12V
• Constant activation current: do 500mA
• Force if can hold: 180kg
• Dimensions: 172 x 40 x 21mm
• Waterproof
MG995 servo is a powerful servo motor that is capable of spinning and controlling things that a small hobby servo motor could never accomplish doing. It comes with a bunch of accessories so you could connect it easily with the outer world, and it’s being controlled like every other servo motor, via PWM.
• RPM: 0.20s/60 degrees (4.8V), 0.16s/60 degrees (6V)
• Voltage: 4.8V – 6.6V
• Torque: 9.4kg/cm (4.8V) – 11kg/cm (6V)
• Angle: 180 degrees
• Dimensions: 40mm x 20mm x 43mm
• Weight: 55g
This module lowers the input voltage to a specific output voltage which you adjust via a trimmer on the board. It is very practical because by changing the input voltage, the output always remains the same. It converts voltages with high efficiency, significantly higher than standard voltage regulators.
• Input Voltage: 4.5V – 28V
• Output Voltage: 0.8V – 20V
• Max. current on the output: 3A
• Efficiency: do 96%
• Dimensions: 22 x 17 x 4 mm
• Current Peak: 4A
• Frequency: 100kHz do 1.5MHz
There is no protection diode in case of wrong polarity, be careful when connecting!
Boost (step up) module. The input voltage increases to the desired one with high efficiency.
• Input voltage: 3.5 – 30 V
• Output voltage: 4.0 -30 V (adjustable)
• Output current: (max) 5A
• Efficency: around 90%, do 94%, depends on input and output voltage
• Dimensions: 52 x 38 x 20 cm
This AC-DC power supply is a simple solution to power your 12V or 5V devices. it is especially practicle for projects where you need both standard voltages. Simply give it AC voltage of 230V from the electrical outlet and it gives you 5V with max 1A and 12V with max 1A.
WARNING: with this module you will work with high voltages! Apply all safety measures, be sure to turn off the power before connecting, and then isolate the high voltage part.
This water pump is extremely easy to use. Soak it in the water or liquid that you want to pump, add a tube to the drain and connect it to the power supply. You can also immerse the pump in the liquid you want to decant. In that case you don’t need to attach a inlet tube in this case. It operates at 12V and is able to expel 240L of fluid per hour.
• Voltage: 12V
• Max. height fluid can reach: 300cm
• Flow rate: 240L/h
• External diameter of drainage tube: 8mm
• Pump dimensions: 55 x 52 x 41 mm
The HLK series power supply makes it very easy to convert high AC voltage to low DC voltage. It does not require external components, although it is recommended to add a fuse and capacitors to the AC input. High efficiency, with overload and short circuit output protection. It meets UL and CE criteria.
• Input voltage: 90V – 264V AC
• Output voltage: 12V
• Output current: 250mA
• Dimensions: 34 x 20.2 x 15 mm
The power supply from the HLK series enables a very simple conversion of high AC voltage into low DC voltage. It does not require external components, although it is recommended to add a fuse and capacitors to the AC input. High efficiency, with protection against overload and short circuit output, meets UL and CE criteria.
• Input voltage: 90V – 264V AC
• Output voltage: 3.3V
• Output current: 900mA
Dimensions: 34 x 20.2 x 15 mm
Plastic platform with slots for two mountable wheels and two DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.
• Material: plastic, transparent
• Type: for two wheels
• Contents: one plastic platform
• Needs to be added: two wheels with DC motors
Plastic platform with slots for four mountable wheels with four DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.
• Material: plastic, transparent
• Type: for four wheels
• Contents: one plastic platform
• Needs to be added: four wheels with DC motors
DC motors can be inconvenient to use on low speed. With the help of mechanic and transfer using sprockets speed of this motor is slowed to a remarkably small speed. It is used for precise control over many mechanisms from robot wheels to precise mechanics.
• Voltage: 3V
• Axle diameter: 3mm
• Dimensions: 12mm x 10mm x 36mm
An aluminum platform with four mountable rubber wheels and four DC motors. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.
• Material: aluminium
• Type: for four wheels
• Motor voltage: 3V – 6V
• Contents: four wheels with gearbox, aluminium plates, required screws and standoffs, battery holder
An aluminum platform with two mountable rubber wheels, two DC motors and balancing third (middle) wheel. Because it’s easy to assemble, it’s great for various hobby and school (robotic) projects. There are many more slots on the platform for various position and distance sensors, LEDs, batteries and controllers.
• Material: aluminium
• Type: for two wheels
• Motor voltage: 3V – 6V
• Contents: two wheels, two DC motors with gearbox, aluminium plate, middle wheel, required screws
Wheel for robotic projects (65mm in diameter) with black tires made of rubber. It will roll your every project, but it doesn’t come with a motor.