Filter
Second filter
Third filter
Fourth filter

Power, Step-up & Step-down

This category includes power supplies and step-up / step-down converters. The well-known step-down LM2596S or step-up XL6009 can be found here.

Showing all 9 results

Sort by:
Step-down module with LM2596S
Step-down module with LM2596S

This module lowers the input voltage on the specified output voltage that you adjust through the trimmer on the board. It’s very practical because while changing the input voltage, the output voltage always stays the same. However, the input voltage has to be at least 0.7V higher than the output voltage.

Input voltage is IN+ and IN-, while the output is OUT+ and OUT- . A power supply is able only to bring the voltage down, not up!

 

It does not have a protective diode in case of the wrong polarity, pay attention while connecting!

Out of stock Step-up module with XL6009
Step-up module with XL6009

Smaller booster (step-up) module. Input voltage is increased to the desired level.

 

• Input voltage: 5-32 V
• Output voltage: 5-35 V (adjustable)
• Input current: (max) 10A
• Efficiency: greater than 94%
• Dimensions: 43mm x 21mm x 14mm

Step-down module MP1584 3A
Step-down module MP1584 3A

This module lowers the input voltage to a specific output voltage which you adjust via a trimmer on the board. It is very practical because by changing the input voltage, the output always remains the same. It converts voltages with high efficiency, significantly higher than standard voltage regulators.

 

• Input Voltage: 4.5V – 28V
• Output Voltage: 0.8V – 20V
• Max. current on the output: 3A
• Efficiency: do 96%
• Dimensions: 22 x 17 x 4 mm
• Current Peak: 4A
• Frequency: 100kHz do 1.5MHz

 

There is no protection diode in case of wrong polarity, be careful when connecting!

Step-up module LM2587
Step-up module LM2587

Boost (step up) module. The input voltage increases to the desired one with high efficiency.

 

Input voltage: 3.5 – 30 V
 Output voltage: 4.0 -30 V (adjustable)
• Output current: (max) 5A
Efficency: around 90%, do 94%, depends on input and output voltage
• Dimensions: 52 x 38 x 20 cm

Power supply 12V 1A 12W, 5V 1A 5W
Power supply 12V 1A 12W, 5V 1A 5W

This AC-DC power supply is a simple solution to power your 12V or 5V devices. it is especially practicle for projects where you need both standard voltages. Simply give it AC voltage of 230V from the electrical outlet and it gives you 5V with max 1A and 12V with max 1A.

 

WARNING: with this module you will work with high voltages! Apply all safety measures, be sure to turn off the power before connecting, and then isolate the high voltage part.

 

Step-up module 150W
Step-up module 150W

Smaller booster (step-up) module. It increases input voltage to the desired level.

 

Panel power supply 12V 3W HLK-PM12
Panel power supply 12V 3W HLK-PM12

The HLK series power supply makes it very easy to convert high AC voltage to low DC voltage. It does not require external components, although it is recommended to add a fuse and capacitors to the AC input. High efficiency, with overload and short circuit output protection. It meets UL and CE criteria.

 

Input voltage: 90V – 264V AC
• Output voltage: 12V
• Output current: 250mA
• Dimensions: 34 x 20.2 x 15 mm

Panel power supply 3.3V 3W HLK-PM03
Panel power supply 3.3V 3W HLK-PM03

The power supply from the HLK series enables a very simple conversion of high AC voltage into low DC voltage. It does not require external components, although it is recommended to add a fuse and capacitors to the AC input. High efficiency, with protection against overload and short circuit output, meets UL and CE criteria.

 

• Input voltage: 90V – 264V AC
• Output voltage: 3.3V
• Output current: 900mA
Dimensions: 34 x 20.2 x 15 mm

Out of stock Panel power supply 5V 3W HLK-PM01
Panel power supply 5V 3W HLK-PM01

The HLK series power supply makes it very easy to convert high AC voltage to low DC voltage. It does not require external components, although it is recommended to add a fuse and capacitors to the AC input. High efficiency, with overload and short circuit output protection. It meets UL and CE criteria.

 

Input voltage: 90V – 264V AC
Output voltage: 5V

• Output current: 600mA
• Dimensions: 34 x 20.2 x 15 mm

items per page