Filter
Second filter
Third filter
Fourth filter

Relays

In this category you will find all relays from our offer. Some of them are: 1-channel relay, 2-channel relay with easyC, SSR relays, etc.

Showing all 9 results

Sort by:
1-channel relay board with easyC
1-channel relay board with easyC

Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

 

This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.

1-channel relay board
1-channel relay board

Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process, because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t even have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

Out of stock 2-channel relay board
2-channel relay board

Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 2 relays.

 

4-channel relay board
4-channel relay board

Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board. This product has 4 relays.

Relay with 5V coil
Relay with 5V coil

Relay is a device with enables switching greater loads – ones that require more voltage/current. These relays can be found in our relays breakouts. It has NO and NC pins.

 

• Current needed for activation (current of Dasduino): 20mA
• Coil voltage: 5V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A

Relay with 12V coil
Relay with 12V coil

The relay 12v coil is a device used to turn (overlapping) large loads – those that require higher voltages or currents. These relays are used on the modules with the relay. There are NO and NC pins.

 

• Current needed for activation: 77mA
• Coil voltage: 12V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A

 

Module with SSR relay, 1-channel
Module with SSR relay, 1-channel

Solid State Relay (SSR) is an electronic switch that can turn a much higher power load on or off at a small input signal. It has the same role as a regular electromechanical relay, only the SSR has no moving parts which eliminates the possability of mehanical faliure.

 

Input voltage/ Output Voltage: 5V/ 240V
Current needed for activation: 2A
• Dimensions: 24 x 32 x 21mm
• Number of channels: 1 – channel

40A Fotek SSR-40DA
40A Fotek SSR-40DA

A solid-state relay SSR 40DA is the same thing as the relay (control power-hungry devices, by using small amounts of voltage and current),  the only difference is that the solid-state version doesn’t have any mobile parts which make it suitable for devices that need to fold quickly.

2-channel relay board with easyC
2-channel relay board with easyC

Did you ever wanted to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is actually an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

 

This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.

items per page