In this category you will find products related to communication. Here are various antennas, breakout boards, bluetooth modules, RFID cards, etc.
Showing 1–24 of 65 results
RFID is a type of communication in which information is transmitted wirelessly (Wikipedia article). Today, it is becoming increasingly popular and can be found in numerous and various cards: driving licenses, access control to buildings, public transportation, etc.
RFID readers come in many shapes and variations. This reader, from our production, allows easy connection to a microcontroller, and thus opens up possibilities for developing various projects based on RFID technology. The breakout comes programmed and ready for I2C communication through the easyC system. It has easyC connectors as well as a connector for antenna that comes with the breakout. On the board, there is also a switch for changing the I2C address.
RFID is a type of communication in which information is transmitted wirelessly (Wikipedia article). Today, it is becoming increasingly popular and can be found in numerous and various cards: driving licenses, access control to buildings, public transportation, etc.
RFID readers come in many shapes and variations. This reader, from our production, allows easy connection to a microcontroller, thereby opening up possibilities for the development of various projects based on RFID technology. The breakout comes programmed and ready for UART communication through the pins on the board. It has a switch to change the data transfer speed (baud rate) and a connector for connecting the antenna that comes with the breakout.
Global Navigation Satellite Signal Systems (GNSS), or as we all like to call it “GPS”, enable precise location determination on Earth. Thanks to this module, you can use GNSS for your project and use the device for asset tracking or create a wearable device. The module is small, energy-efficient, high-performing, and easy to use thanks to the built-in antenna.
L86-M33 is a GNSS receiver, which means it can receive signals from GPS, GLONASS, and Galileo constellations. Equipped with EASY (Embedded Assist System for self-generated orbit prediction) and AlwaysLocate technologies, L86-M33 ensures fast and accurate positioning even in challenging environments. Its advanced internal logger LOCUS allows you to store your routes and location data.
Our breakout board, in addition to the previously mentioned L86-M33 module which has an integrated antenna, also has a connector for a CR1220 battery which is used as a backup for timekeeping and GPS data. The module can operate without the battery, but every time it will have to fetch data from satellites afresh (cold start). If the integrated antenna is insufficient, there is an IPX connector on the board for adding an external, stronger antenna. The antenna we suggest can be found here. To easily access the module pins, the pins are extended on the board for accessibility. There is also a switch on the board to change the I2C address.
If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.
Global Navigation Satellite Systems (GNSS), or as we all like to call it “GPS,” enable precise location determination on Earth. Thanks to this module, you can use GNSS for your project and employ the device for asset tracking or create a wearable device. The module is small, energy-efficient, highly effective, and easy to use thanks to its built-in antenna.
L86-M33 is a GNSS receiver, meaning it can receive signals from GPS, GLONASS, and Galileo constellations. Equipped with EASY (Embedded Assist System for self-generated orbit prediction) and AlwaysLocate technologies, the L86-M33 ensures fast and accurate positioning even in challenging environments. Its advanced internal logger, LOCUS, allows you to store your routes and location data.
In addition to the aforementioned L86-M33 module, which has an integrated antenna, our breakout board also has a connector for a CR1220 battery that is used as a backup for timekeeping and GPS data. The module can operate without a battery, but each time it will have to pull data from the satellites anew (cold start). If the integrated antenna is not sufficient, there is an IPX connector on the board for adding an external, stronger antenna. You can find the antenna we recommend here. To easily access the pins of the module, the pins are exposed on the board for easy access.
easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.
This product is easyC compatible cable, with easyC connectors on both sides lenght 10cm.
IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male
If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.
Infra-red (IR) diode emits light in the spectrum that the human eye can’t see. However, such a diode has its purpose. It is used in remote controllers that send information on wavelengths within the infrared spectrum, e.g. to change television programme. So all you need to create your own remote is one of these diodes and correct data which will be sent!
• Diameter: 5mm
• Voltage: 1.2V – 1.6V
• Current: typical 100mA
NRF24L01+ module enables wireless two-way communication between two Dasduinos. Its range is up to 100m outdoors. With some adjustments of the antenna, the range can be larger.
WiFi antenna with standard SMA male connector for connecting to your PCBs.
• Connector: SMA male
• Impedance: 50 ohm
• Frequency: 2.4GHz
• Dimensions: 50.5 x 19 x 10mm
This LoRa antenna is specially designed for use with the LoRa protocol. Through detailed testing, we have determined that it achieves maximum range in open spaces and we recommend it for use with external gateways.
• Mounting type: pole, comes with a holder
• Connector: N-type
• Gain: 6.5dBi
• Frequency: 868MHz (Europe)
• Impedance: 50 ohm
• Dimensions: 55 x 2.6 cm
This set enables controlling different devices through IR connection. Apart from the remote controller that comes inside this package, you can use any other remote controller and program it as you wish. Connecting the IR receiver with Dasduino is simple using just one wire, and the complete system works on standard frequency for IR control 38kHz.
Additional passive RFID tag for use with our RFID readers. It si practical as key ring.
• Frequency: 125kHz
• Dimensions: 30 x 40 x 3 mm
This small USBUART adapter converts USB communication into UART (serial) communication, and everything you might need is already on this small board. In addition to the classic UART pins that are arranged in the standard layout: DTR, RXD, TXD, VCC, CTS, GND, other pins available of the CH340 chip are also available on header: RS232, RI, DCD, DSR, RST and CTS. Indication LEDs show activity on RXT and TXD lines, and a 500mA fuse protects this programmer, the USB port of the computer that is connected, and other devices connected to it from damage.
Additionally, there is a voltage regulator and a switch on the board, and it is possible to choose the output voltage of 3.3V or 5V, depending on the device you are using. The logic of the UART signal is always 3.3V, but don’t worry, 5V devices will work with 3V3 UART logic without any problems. Use a USB-C cable to connect.
RFID card is white and the size of the standard credit card. We promise that it will fit into any standard wallet! It comes with a random unique code.
SIM800 is a well-known chip for GSM / GPRS (2G mobile network) communication. Insert a SIM card, call, send SMS and connect to the Internet using a microcontroller. This breakout allows these connections in a simple way, it communicates with Arduino over a serial link. It is programmed using Arduino’s already finished libraries. Breakout even comes with a small wire antenna that will be sufficient for testing and use in areas where the signal is corresponding!
CONNECT programmer is designed to allow extremely simple programming of boards based on ESP8266 and ESP32 microcontrollers. It contains all the necessary electronics and logic so that programming can be done by plugging USB cable into CONNECT programmer and connecting CONNECT programmer to the programming header. Electronics that take care of timing and signal sequence are also on board, so it puts the ESP uC into bootloader mode.
ESP programming header can be found boards made by Soldered based on ESP8266 or ESP32 microcontrollers that do not have a USB-UART converter, but this programmer can be used for any other ESP32 / ESP8266 board as well.
• IC: CH340
• Pin layout: GPIO0, RESET, RX, TX, 3V3, GND
• LEDs: RX, TX, power
• USB: USB-C
• Dimensions: 38 x 22 mm
ESP8266 is an IC that delivers a true revolution in the world of makers, especially in the world of IoT (Internet of Things). This is a complete 32-bit SoC (System on Chip) with built-in flash memory, frame and EEPROM which can even be programmed directly from the Arduino interface, without the need for additional micro-controller. With all this, the most important point is that in itself has a built-in WiFi (AP, STA, AP + STA), all that for “little money”.
ESP8266 in this form (ESP-12) is suitable for direct soldering to a printed circuit board as an SMD component or directly solder the wires since the pin has its holes. It also comes with a PCB trace antenna.
Note: ESP8266 is an IC that works at 3.3V! Connecting directly to 5V, or track Arduino or Croduino plate will destroy it! Use logic level converter.
The ESP32 is a more advanced successor to the well-known ESP8266. It is a SoC (System on Chip) that can function as a standalone microcontroller and has everything you need on WiFi and Bluetooth 4.0 (BLE 4.0, low-energy) communication. With nearly 30 I / O pins and low power consumption, ESP32 will almost certainly be the leader in the Internet of Things for years to come.
The microcontroller itself works at a frequency of 160MHz (up to 240MHz), while the module has a built-in flash memory of 4MB. It has all the classic protocols like 4x SPI, 2x I2C, 4x UART, and there are many built-in peripherals like 18x 12-bit ADC, 2x 8-bit DAC, 10x capacitive touch GPIO, temperature sensor, SD card controller, Ethernet interface, PWM, etc. The list is really long. It should not be forgotten that this module has FCC certification and PCB trace antenna.
• SoC: ESP32
• CPU: Xtens 32-bit LX6, 160MHz to 240MHz
• Flash memory: 4MB
• RAM memory: 520kB
• Exact module name: ESP-WROOM-32
• Number of pins: 38
• Dimensions: 18 x 25.5 x 2.8 cm
The active GPS antenna allows you to get a better GPS signal reception to your device. The antenna comes with a 3m cable at the end of which is the classic SMA male connector. There is a magnet for easier installation at the bottom of the antenna.
• Connector: SMA male
• Frequency: 1575.42MHz
• Voltage: 3V-5V
• Current: 10mA max.
• Polarization: circular(RH)
• Amplification: 28dB
• Dimensions: 45mm x 39mm x 13mm
GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.
RFID card is white and the size of standard credit card. We promise that it will fit into any standard wallet! Comes with random unique code.
• Frequency: 125kHz