Ethernet & Wifi

In this category you will find antennas, microcontrollers and modules for ethernet / WiFi. For example, the Arduino Ethernet shield with W5100 or the well-known ESP8266.

Showing all 8 results

Sort by:
ESP8266 ESP-12 WiFi Module
ESP8266 ESP-12 WiFi Module

ESP8266 is an IC that delivers a true revolution in the world of makers, especially in the world of IoT (Internet of Things). This is a complete 32-bit SoC (System on Chip) with built-in flash memory, frame and EEPROM which can even be programmed directly from the Arduino interface, without the need for additional micro-controller. With all this, the most important point is that in itself has a built-in WiFi (AP, STA, AP + STA), all that for “little money”.

ESP8266 in this form (ESP-12) is suitable for direct soldering to a printed circuit board as an SMD component or directly solder the wires since the pin has its holes. It also comes with a PCB trace antenna.


 

Note: ESP8266 is an IC that works at 3.3V! Connecting directly to 5V, or track Arduino or Croduino plate will destroy it! Use logic level converter.

 

Out of stock ESP32-WROOM-32D WiFi module
ESP32-WROOM-32D WiFi module

The ESP32 is a more advanced successor to the well-known ESP8266. It is a SoC (System on Chip) that can function as a standalone microcontroller and has everything you need on WiFi and Bluetooth 4.0 (BLE 4.0, low-energy) communication. With nearly 30 I / O pins and low power consumption, ESP32 will almost certainly be the leader in the Internet of Things for years to come.

The microcontroller itself works at a frequency of 160MHz (up to 240MHz), while the module has a built-in flash memory of 4MB. It has all the classic protocols like 4x SPI, 2x I2C, 4x UART, and there are many built-in peripherals like 18x 12-bit ADC, 2x 8-bit DAC, 10x capacitive touch GPIO, temperature sensor, SD card controller, Ethernet interface, PWM, etc. The list is really long. It should not be forgotten that this module has FCC certification and PCB trace antenna.

 

SoC: ESP32
CPU: Xtens 32-bit LX6, 160MHz to 240MHz
• Flash memory: 4MB
• RAM memory: 520kB
Exact module name: ESP-WROOM-32
• Number of pins: 38
Dimensions: 18 x 25.5 x 2.8 cm

Ethernet controller W5500 board
Ethernet controller W5500 board

Designed with practicality in mind, this small yet powerful breakout contains the W5500 Ethernet controller, enabling fast and reliable internet connection for your Dasduino projects. Whether you’re an experienced enthusiast or just a beginner, this module is your reliable ally for connecting your Dasduino CORE to the internet.

 

In addition to the mentioned controller, the board features an RJ-45 connector for Ethernet cable connection, and the connection to Dasduino is via the SPI protocol.

 

So, whether you want to build a smart home automation system, create an IoT device with web connectivity, or simply explore the world of networked electronics with your Dasduino, the W5500 breakout is here. Say goodbye to connection problems and welcome the world of endless possibilities – all with the help of this little marvel!

WiFi 2.4G PCB antenna with IPX connector TX2400-FPC-5015
WiFi 2.4G PCB antenna with IPX connector TX2400-FPC-5015

If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.

WiFi 2.4G antenna with SMA connector, vertical
WiFi 2.4G antenna with SMA connector, vertical

WiFi antenna with standard SMA male connector for connecting to your PCBs.

 

• Connector: SMA male
• Impedance: 50 ohm
• Frequency: 2.4GHz
Dimensions: 50.5 x 19 x 10mm

WiFi 2.4G/5G antenna with IPX connector
WiFi 2.4G/5G antenna with IPX connector

If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.

WiFi 2.4G PCB antenna with IPX connector
WiFi 2.4G PCB antenna with IPX connector

If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.

USB WiFi adapter
USB WiFi adapter

If your device lacks WiFi, connect this device to USB and the problem is solder! WiFi USB adapter works on all major operating systems. It comes with an external SMA antenna that you can also unplug and connect a stronger antenna if required.

items per page