Communication

This cabel switches your antenna with an SMA female connector to an N-type connector.

• Cable lenght: 1m

This antenna is designed for LoRa modules based on 868MHz frequency (Europe).

• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 79mm
• Connector type: SMA male

This antenna is designed for LoRa modules based on 868MHz frequency (Europe).

• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male

This antenna is designed for LoRa modules based on 868MHz frequency (Europe). It is soldered on a hole in PCBs and has a significantly better sensitivity compared to ordinary wire.

• Frequency range: 868MHz
• Impedance: 50ohm
• Diameter: 5mm
• Lenght (spiral): 14mm

This LoRa antenna is specially designed for use with the LoRa protocol. Through detailed testing, we have determined that it achieves maximum range in open spaces and we recommend it for use with external gateways.

• Mounting type: pole, comes with a holder
• Connector: N-type
• Gain: 6.5dBi
• Frequency: 868MHz (Europe)
• Impedance: 50 ohm
• Dimensions: 55 x 2.6 cm

WiFi antenna with standard SMA male connector for connecting to your PCBs.

• Connector: SMA male
• Impedance: 50 ohm
• Frequency: 2.4GHz
• Dimensions: 50.5 x 19 x 10mm

GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.

This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.

• Frequency: 4GHz/LTE
• Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm

This product has IPX connectors on both ends they are gold color and its lenght is. Connects easily and has good connection.

• lenght: 10cm

If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.

If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.

Additional passive RFID tag for use with our RFID readers. It si practical as key ring.

RFID tag comes in two variants, 125kHz or 13.56MHz.

Universal IR (infrared) remote with 6 keys: ignition key, four direction keys, and center button. Although it is intended for something else, you will easily pair this IR remotely with an IR receiver in the Croduino / Arduino project and thus make it respond to your commands.

• Number of buttons: 21
• Battery: CR2025, comes with the remote
• Dimensions: 86 x 40 x 6.5mm

IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.

easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.

easyC-compatible cables with easyC connectors on both ends, available in different lengths.

443MHz RF is an accessible and affordable standard for RF communication between two devices (e.g. two Dasduino boards or between a remote controller and Dasduino with receiver) often used for remote control, wireless communication and data transmission. With this remote, commands are sent at 433MHz frequency and it’s able to send 4 different commands in total.

443MHz RF is an accessible and affordable standard for RF communication between two devices (e.g. two Dasduino boards or between a remote controller and Dasduino with receiver) often used for remote control, wireless communication and data transmission. This combination allows you to communicate with a remote control that has four buttons with one receiver.

If your device lacks WiFi, connect this device to USB and the problem is solder! WiFi USB adapter works on all major operating systems. It comes with an external SMA antenna that you can also unplug and connect a stronger antenna if required.

The active GPS antenna allows you to get a better GPS signal reception to your device. The antenna comes with a 3m cable at the end of which is the classic SMA male connector. There is a magnet for easier installation at the bottom of the antenna.

• Connector: SMA male
• Frequency: 1575.42MHz
• Voltage: 3V-5V
• Current: 10mA max.
• Polarization: circular(RH)
• Amplification: 28dB
• Dimensions: 45mm x 39mm x 13mm

Infra-red (IR) diode emits light in the spectrum that the human eye can’t see. However, such a diode has its purpose. It is used in remote controllers that send information on wavelengths within the infrared spectrum, e.g. to change television programme. So all you need to create your own remote is one of these diodes and correct data which will be sent!

The IR receiver is a device that detects the modulated IR radiation emitted by the remote controls. The IRM-56384 detects IR radiation on a standard frequency of 38kHz and outputs signal to its output pin, which can be read with a microcontroller. Thus, it enables project management via the remote control.

RFID card is white and the size of standard credit card. We promise that it will fit into any standard wallet! Comes with random unique code.

RFID card comes in two variants, 125kHz or 13.56MHz.

This antenna is designed for 433MHz modules from our offer and improves their range even up to 300%. It works both as a receiver and as an emitter.

• Frequency range: 433MHz (+-6MHz)
• Amplification: 2.2dBi
• Impendance: 50ohm
• Maximum power: 30dBi

The ceramic antenna at a frequency of 1575.42MHz corresponding GPS. Ideal with our SIM808 breakout.