Filter
Second filter
Third filter
Fourth filter

Communication

In this category you will find products related to communication. Here are various antennas, breakout boards, bluetooth modules, RFID cards, etc.

Showing 25–48 of 57 results

Sort by:
Out of stock NRF24L01 adapter for Dasduino boards
NRF24L01 adapter for Dasduino boards

Connecting the NRF24L01 can be tricky – you have to pay attention to the layout of the pins, adjust them to match those from the library and add a capacitor. This board solves all that, and it already comes with soldered headers, so just plug this board into your Dasduino and that’s it!

 

• Comes with NRF24L01+ module
• Dimensions
: 38 x 22 mm

433MHz RF transmitter and receiver
433MHz RF transmitter and receiver

RF transmitter and receiver is a high-quality combination for RF communication between two devices (eg. Dasduino) often used for remote controlling or wireless communication.

433MHz 4-channel remote controller
433MHz 4-channel remote controller

443MHz RF is an accessible and affordable standard for RF communication between two devices (e.g. two Dasduino boards or between a remote controller and Dasduino with receiver) often used for remote control, wireless communication and data transmission. With this remote, commands are sent at 433MHz frequency and it’s able to send 4 different commands in total.

433MHz 4-channel receiver + remote controller
433MHz 4-channel receiver + remote controller

443MHz RF is an accessible and affordable standard for RF communication between two devices (e.g. two Dasduino boards or between a remote controller and Dasduino with receiver) often used for remote control, wireless communication and data transmission. This combination allows you to communicate with a remote control that has four buttons with one receiver.

433MHz antenna
433MHz antenna

This antenna is designed for 433MHz modules from our offer and improves their range even up to 300%. It works both as a receiver and as an emitter.

 

Frequency range: 433MHz (+-6MHz)
Amplification: 2.2dBi
Impendance: 50ohm
Maximum power: 30dBi

Antenna LoRa 868MHz SMA
Antenna LoRa 868MHz SMA

This antenna is designed for LoRa modules based on 868MHz frequency (Europe).

 

Frequency range: 868MHz (Europe)
Impedance: 50ohm
6dBi
Length: 261mm
• Connector type: SMA male

LoRa 868MHz wire antenna
LoRa 868MHz wire antenna

This antenna is designed for LoRa modules based on 868MHz frequency (Europe). It is soldered on a hole in PCBs and has a significantly better sensitivity compared to ordinary wire.

 

Frequency range: 868MHz
Impedance: 50ohm
• Diameter: 5mm
Lenght (spiral): 14mm

4G/LTE PCB antenna with IPX connector
4G/LTE PCB antenna with IPX connector

This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.

 

• Frequency: 4GHz/LTE
Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm

Bluetooth module HM-10 (BLE 4.0)
Bluetooth module HM-10 (BLE 4.0)

Bluetooth Module HM-10 enables Bluetooth 4.0 (BLE 4.0) communication between your project and another Bluetooth device, such as mobile phone. A connection with Croduino is simple via serial communication and the module operates at standard voltage of 3.3V and 5V. This module will work with iOS6 and higher systems as well as with Android 4.3 and greater.

Bluetooth standard: 4.0
• works with iOS6 or higher and  Android 4.3 or higher
Voltage: 3V – 6V
• Current: 60uA – 400uA
• Antenna: on the PCB
Dimensions: 43mm x 16mm

RS-232 transciever breakout
RS-232 transciever breakout

The RS-232 is a standard and very popular protocol for communication between two devices. It is a full-duplex protocol which means it can receive and send data at the same time, and data is sent at voltages from + 3V to + 15V for a digital “one” and from -3V to -15V for digital “zero”. This provides a more secure environment for data transmission which is resistant to noise or interference, which is why the RS-232 is often used in industry. This module converts serial communication to RS232.

 

Communication lines: TX, RX
IC:232 MAX

Voltage: 3.3V – 5.5V
• Dimensions: 22 x 22 mm

Logic level converter board
Logic level converter board

This logic level converter board module gives us a translation of logic level between two signals. In layman’s terms, if we take a signal with logical “unit” on 5V convert into a signal which logical “unit” has on 3.3V this module will help us. Something like this is useful in this case if we want to achieve communication between two devices from whom one works on 5V and the other on 3.3V, or any other combination of voltages. Directly connecting we would “burn” a device that works on 3.3V and a module gives us to avoid that.

 

Max. voltage: 30V
• Number of channels: 4
Dimensions: 22 x 22mm

RS-485 transciever breakout
RS-485 transciever breakout

This module allows you to connect a Dasduino, or similar microcontroller, to a RS-485 communication protocol. The RS-485 is used to send data over long distances (up to 1200m) at 20Mbps and in high-noise environments, such as industrial. The module works on 5V and requires between 120μA and 500μA of current.

 

Voltage: 5V
Based on: SN65176BDR
• Dimensions: 38 x 2mm

CAN Transceiver MCP2518 board
CAN Transceiver MCP2518 board

CAN Transceiver (Controller Area Network) is a network technology that enables fast communication between microcontrollers, and is the most commonly used standard in cars. Our CAN breakout uses an MCP2518FD CAN whose communication between microcontrollers takes place on SPI protocol. In addition there is a CAN transceiver. This breakout allows use of both standards (CAN 2.0B and CAN Flexible Data (FD)). Access to the CAN bus is possible via CANH and CANL pins on the screw terminal. The 120ohm terminator resistor is also located on the board and can be connected to a jumper.

 

Standards: CAN 2.0B i CAN FD
• Voltage: 2.7V i 5V
Current: from 10uA to 12mA
SPI interface
Dimensions: 38 x 22 mm

IR receiver 40kHz
IR receiver 40kHz

The IR receiver is a device that detects the modulated IR radiation emitted by the remote controls. The IRM-56384 detects IR radiation on a standard frequency of 38kHz and outputs signal to its output pin, which can be read with a microcontroller. Thus, it enables project management via the remote control.

Bluetooth audio module OVC3860
Bluetooth audio module OVC3860

The Bluetooth audio module allows you to stream, ie. transfer audio from a device (such as a cell phone or laptop) to this module via Bluetooth.

 

• Range: 10m
• Baud rate: 3Mbps
Voltage: 3.6V – 4.2V
• Current: 55mA
• Dimension: 16 x 29 x 2.3mm

Out of stock VK172 USB GPS module
VK172 USB GPS module

This U-blox7 GPS / GLONASS module connects to USB and can be used to obtain GPS coordinates.

To use this module, drivers from the official website must be installed.

I2C multiplexer TCA9548A breakout
I2C multiplexer TCA9548A breakout

Have you ever found yourself wanting to connect more than one I2C device to a single controller and couldn’t because they have identical I2C addresses? There you have it, I2C multiplexer (I2C MUX) allows you to use up to 8 devices with the same address on the same bus! If we mention that TCA9548A, the IC on which this breakout is based, has three adjustable pins for the I2C address, which means a total of 8 possible addresses. We can reach 64 devices with the same address on the same bus. For example, it is possible to connect 64 BME680 sensors that are read by only one microcontroller.

 

This adapter is particularly practical because it enables multiplexing of easyC devices.

IR remote controller
IR remote controller

Universal IR (infrared) remote with 6 keys: ignition key, four direction keys, and center button. Although it is intended for something else, you will easily pair this IR remotely with an IR receiver in the Croduino / Arduino project and thus make it respond to your commands.

 

Number of buttons: 21
Battery: CR2025, comes with the remote
Dimensions: 86 x 40 x 6.5mm

Ceramic GPS antenna 1575.42MHz with IPX connector
Ceramic GPS antenna 1575.42MHz with IPX connector

The ceramic antenna at a frequency of 1575.42MHz corresponding GPS. Ideal with our SIM808 breakout.

 

LIN Transceiver NCV7329 breakout
LIN Transceiver NCV7329 breakout

LIN (Local Interconnect Network) is a serial network protocol used for communication between components in cars. The LIN bus is an alternative to the CAN bus, and the difference is that LIN has a lower speed and supports a smaller number of simultaneous devices, but also has drastically lower costs. LIN is used for communication between microcontrollers. The operating voltage is 18V.

 

Master/Slave is a communication model where one device (Master) controls one or more devices (Slave), and the Slave then listens to the commands it receives from the Master. One Master on the LIN protocol can control up to 16 devices.

LoRa 868MHz antenna 79mm
LoRa 868MHz antenna 79mm

This antenna is designed for LoRa modules based on 868MHz frequency (Europe).

 

Frequency range: 868MHz (Europe)
Impedance: 50ohm
• Lenght: 79mm
• Connector type: SMA male

Out of stock MFRC-522 RFID 13.56MHz reader
MFRC-522 RFID 13.56MHz reader

RFID is a kind of communication where the information is transferred wirelessly. Nowadays it is more and more popular and can be found in numerous and different kinds of cards: driver’s license, access control to facilities, public transport, etc. This module brings in that kind of communication to Croduino, a reader reads off information from the RFID card or tag and sends them to Croduino through SPI communication.

microSD card reader breakout
microSD card reader breakout

A module which enables the use of micro SD cards with Arduino via SPI communication. You can save various types of data on the SD card, create logs, read the information from it or perform various actions.

Logic level converter generic TXB0104 breakout
Logic level converter generic TXB0104 breakout

This small and simple module gives us a translation of logic level between two signals. In layman’s terms, if we take a signal with logical “unit” on 5V convert into a signal which logical “unit” has on 3.3V this module will help us. Something like this is useful in this case if we want to achieve communication between two devices from whom one works on 5V and the other on 3.3V, or any other combination of voltages. Directly connecting we would “burn” a device that works on 3.3V and a module gives us to avoid that.

 

This board is specialized for signal conversion for any communication protocol, and for this conversion, it uses a special integrated circuit that enables communication at high speeds.

 

Max. voltage: 30V
• Number of channels: 4
Communication protocol: any besides I2C
Dimensions: 22 x 22mm

items per page