All the antennas we offer are in this category. WiFi antennas with IPX connector, IPX to SMA adapter cable, GPS, GSM, LoRa, etc.
Showing all 21 resultsSorted by average rating
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 200mm
• Connector type: SMA male
If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.
Waterproof and high quality antenna connection cable, used as standard to connect LoRa antennas to the LoRa gateway.
• Connector A: SMA Male
• Connector B: N-Type Male
• Impedance: 50Ω
• Cable length: 1m
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• 6dBi
• Length: 261mm
• Connector type: SMA male
This connector allows the connection of an antenna with a male SMA connector to a board at a 90-degree angle.
This cabel switches your antenna with an SMA female connector to an N-type connector.
• Cable lenght: 1m
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 79mm
• Connector type: SMA male
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male
This antenna is designed for LoRa modules based on 868MHz frequency (Europe). It is soldered on a hole in PCBs and has a significantly better sensitivity compared to ordinary wire.
• Frequency range: 868MHz
• Impedance: 50ohm
• Diameter: 5mm
• Lenght (spiral): 14mm
This LoRa antenna is specially designed for use with the LoRa protocol. Through detailed testing, we have determined that it achieves maximum range in open spaces and we recommend it for use with external gateways.
• Mounting type: pole, comes with a holder
• Connector: N-type
• Gain: 6.5dBi
• Frequency: 868MHz (Europe)
• Impedance: 50 ohm
• Dimensions: 55 x 2.6 cm
WiFi antenna with standard SMA male connector for connecting to your PCBs.
• Connector: SMA male
• Impedance: 50 ohm
• Frequency: 2.4GHz
• Dimensions: 50.5 x 19 x 10mm
GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.
This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.
• Frequency: 4GHz/LTE
• Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm
If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.
IPX SMD connector for soldering to the printed circuit board. It is most commonly used with antennas, and the impedance is 50 ohms.
If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.
IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.
The active GPS antenna allows you to get a better GPS signal reception to your device. The antenna comes with a 3m cable at the end of which is the classic SMA male connector. There is a magnet for easier installation at the bottom of the antenna.
• Connector: SMA male
• Frequency: 1575.42MHz
• Voltage: 3V-5V
• Current: 10mA max.
• Polarization: circular(RH)
• Amplification: 28dB
• Dimensions: 45mm x 39mm x 13mm
GSM SMA Connector antenna with standard SMA male connector for connecting to your GSM PCBs.
• Amplification: 3dBi
• Frequency range: 900 – 1800 MHz
• Length: 50mm
• Vertical polarization
This antenna is designed for 433MHz modules from our offer and improves their range even up to 300%. It works both as a receiver and as an emitter.
• Frequency range: 433MHz (+-6MHz)
• Amplification: 2.2dBi
• Impendance: 50ohm
• Maximum power: 30dBi
The ceramic antenna at a frequency of 1575.42MHz corresponding GPS. Ideal with our SIM808 breakout.