In this category there are various electronic components that we offer. Resistors, capacitors, transistors, connectors, etc.
Showing 49–72 of 248 results
The DIP switch is a small switch that is simply used with breadboard or protoboard.
• Number of poles: 5
• Pitch: (2.54mm)
SPDT (single-pole, dual-throw) is simple switch which connects central contact with one of the other two contacts located inside its housing.
SPDT (single-pole, dual-throw) is simple switch which connects central contact with one of the other two contacts located inside its housing.
DPDT (Dual Pole Dual Throw) for PCB mounting. Disconnects two poles simultaneously.
SPDT (single-pole, dual-throw) is a simple sliding switch that connects the central contact with one of the other two contacts in its housing.
IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male
If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.
A socket for standard 8-pin DIL integrated circuit.
The USB Type-C is ubiquitous. We always wanted to add it to our electronics projects, and we’re sure you did too. Adding a USB Type-C connector to your projects is easier than ever thanks to this USB Type-C breakout board. It will allow you to send data to your device, as well as add power to the circuit.
The USB Type-C connector’s GND, CC2, SBU2, D-, D+, SBU1, CC1, and VUSB pins are broken out to the plated through-holes.
Product usage tips:
Male headers that are included need to be soldered to the board. The breakout board has two mounting holes and can be placed on any surface.
The MicroUSB is still everywhere around us, even though it’s slowly being replaced with USB Type-C. We’re sure you wanted to add it to your electronics projects. We did, too, that’s why we added the MicroUSB female connector breakout board to our roster!
The Micro B USB connector’s GND, ID, D+, D-, and VCC pins are broken out to the plated through-holes.
Product usage tips:
The pins included need to be soldered to the board. It won’t move an inch when mounted with the two mounting holes.
The USB Type-A connection is still prevalent. If it’s in the electronic devices everywhere around us, it is only natural that we’d want it in our electronic projects. Adding a USB Type-A connection to your circuit is as easy as pie with this breakout board.
The breakout board breaks the GND, D+, D-, and VUSB pins out to the plated through-holes.
Dimensions: 22 mm x 22 mm
Connectors: USB Type-A (female)
Mounting holes: 2
The USB Type-A connection is still prevalent. If it’s in the electronic devices everywhere around us, it is only natural that we’d want it in our electronic projects. Adding a USB Type-A connection to your circuit is as easy as pie with this breakout board.
The breakout board breaks the GND, D+, D-, and VUSB pins out to the plated through-holes.
Product usage tips:
Male headers for the pads are added and need to be soldered. The breakout board has two mounting holes for placing it on different surfaces.
USB type C female connector for PCBs. This connector allows only power but not communication.
Micro-USB SMD connector for soldering to the printed circuit board. The same as it’s used to Croduino Nova, CP2102 USB to UART adapter.
Standard USB A type connector for the Printed Circuit Board(PCB). It can be used as the USB connection, connection for the charger or something else.
IPX SMD connector for soldering to the printed circuit board. It is most commonly used with antennas, and the impedance is 50 ohms.
Classical male header with 2.54mm pin spacing (0.1 ‘). 40-pin.
Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.
Banana connectors are quite standard connectors in electronic labs because they allow fast and firm connection.
Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.
• Diameter: 4mm
• Color: red
• Male connector
Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.
• Diameter: 4mm
• Color: black
• Male connector
Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.
Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.