In this category there are various electronic components that we offer. Resistors, capacitors, transistors, connectors, etc.
Showing 73–96 of 192 resultsSorted by average rating
The USB Type-C is ubiquitous. We always wanted to add it to our electronics projects, and we’re sure you did too. Adding a USB Type-C connector to your projects is easier than ever thanks to this USB Type-C breakout board. It will allow you to send data to your device, as well as add power to the circuit.
The USB Type-C connector’s GND, CC2, SBU2, D-, D+, SBU1, CC1, and VUSB pins are broken out to the plated through-holes.
Product usage tips:
Male headers that are included need to be soldered to the board. The breakout board has two mounting holes and can be placed on any surface.
The MicroUSB is still everywhere around us, even though it’s slowly being replaced with USB Type-C. We’re sure you wanted to add it to your electronics projects. We did, too, that’s why we added the MicroUSB female connector breakout board to our roster!
The Micro B USB connector’s GND, ID, D+, D-, and VCC pins are broken out to the plated through-holes.
Product usage tips:
The pins included need to be soldered to the board. It won’t move an inch when mounted with the two mounting holes.
BC-327 is PNP transistor for generic usage in THT packaging.
• Type: PNP
• Part Number: BC-327
A 500k variable resistance potentiometer that fits the experimental board, but can also be built into the housing due to its increasing size. They can be used for various types of control, eg adjusting how bright the LED is.
This small LED is not just an ordinary LEDs – it’s specific because it has a built-in small integrated circuit (IC) that is able to turn on the LED light in 16 million different colors. IC is WS2812 and it uses a single wire can control thousands of these LEDs. With a little imagination by putting these pixels, you get superior effects with a minimum effort. These lamps are easy to control with Croduino.
• Color: RGB (red/green/blue)
• Voltage: 5V
• Power: max. 60mA
• Diode type: WS2812 SMD LED (5050 LED diode with built IC)
• Dimensions: diameter of 8 mm
A 7-segment display is a classic, frequently used and already familiar component. Size of the digit on the display is 0.56inch and the light it transmits is red. The display has a common anode.
The WS2812B is a smart LED light source with an integrated control circuit and RGB diode. Unlike traditional RGB light sources, the WS2812B is much easier to operate since only one digital control signal is required.
ESP32-WROVER is a powerful microcontroller which has the possibility of wide application as it is possible to modify the processor clock and use its substantial memory. For these reasons, ESP32-WROVER can be used not only in conditions where low power consumption is required but also in situations where high speed is required to process large amounts of data.
The ESP32-WROVER comes with a PCB antenna and offers WiFi and Bluetooth 4.2 connectivity. The core of the module is the ESP32-D0WDQ6 chip. The operating frequency ranges from 80MHz up to 240MHz and the microcontroller can be used with 4MB of flash memory. The freeRTOS operating system drives the ESP32.
SoC: ESP32
Number of pins: 38
Number of GPIO pins: 32
Voltage: 2.3 V – 3.6 V, recommended: 3.3 V
Current: maximum 500 mA, average 80 mA
Operating temperature: -40 – 85 ° C
Chip: ESP32-D0WDQ6
Microprocessors: Xtensa 32-bit LX6
Flash: 4 MB
PSRAM: 8 MB
Dimensions: 18 x 31 x 3.30 mm
Classic male header with a pin spacing of 2.54mm (0.1″). The pin layout is 20 x 2.
5mm RGB LED diode in through-hole version with 4 pins. Each of those represents one color (-), while longest pin is common anode(common +) for all three colors.
• Voltage: 3.4V for blue and green, 2.3V for red
• Current: 20mA per color, total max. 60mA
• Diode size: 5mm, diffused
• Light angle: 25 degrees
This RF converter is used to connect coaxial cables. The converter has a male input on one side and a male output on the other.
This connector allows the connection of an antenna with a male SMA connector to a board at a 90-degree angle.
Classic current adapter from switching the american to european type connector.
• Dimensions: 25.5 x 30 x 14mm
This cabel switches your antenna with an SMA female connector to an N-type connector.
• Cable lenght: 1m
Are you repairing or developing electronic boards? This set of inductors is incredibly useful because you will never have to think again if you have that specific inductor. It consists of 52 different values each of which comes in an amount of 50 pieces.
• Package: 0603
• 25 pcs of 52 values = 1300 pcs
• Values [H]:
1nH, 10nH, 100nH, 1uH, 10uH
1.2nH, 12nH, 120nH, 1.2uH, 12uH
1.5nH, 15nH, 150nH, 1.5uH, 15uH
1.8nH, 18nH, 180nH, 1.8uH, 22uH
2.2nH, 22nH, 220nH, 2.2uH,
2.7nH, 27nH, 270nH, 2.7uH,
3.3nH, 33nH, 330nH, 3.3uH,
3.9nH, 39nH, 390nH, 3.9uH,
4.7nH, 47nH, 470nH, 4.7uH,
5.6nH, 56nH, 560nH, 5.6uH,
6.8nH, 68nH, 680nH, 6.8uH,
8.2nH, 82nH, 820nH, 8.2uH,
Are you repairing or developing electronic boards? This This 0402 SMD resistor set is incredibly useful because you will never have to think again if you have that specific resistor. It consists of 170 different values each of which comes in an amount of 50 pieces. The resistors are manufactured by YAEGO, 1% tolerance and 0402.
• Package: 0402
• Tolerance: 1%
• 50 pcs of 170 values = 8500 pcs
• Resistance values[ohm]:
0, 1, 10, 100, 1K, 10K, 100K, 1M, 10M
1.1, 11, 110, 1.1K, 11K, 110K, 1.1M
1.2, 12, 120, 1.2K, 12K, 120K, 1.2M
1.3. 13, 130, 1.3K, 13K, 130K, 1.3M
1.5, 15, 150, 1.5K, 15K, 150K, 1.5M
1.6, 16, 160, 1.6K, 16K, 160K, 1.6M
1.8, 18, 180, 1.8K, 18K, 180K, 1.8M
2, 20, 200, 2K, 20K, 200K, 2M
2.2, 22, 220, 2.2K, 22K, 220K, 2.2M
2.4, 24, 240, 2.4K, 24K, 240K, 2.4M
2.7, 27, 270, 2.7K, 27K, 270K, 2.7M
3, 30, 300, 3K, 30K, 300K, 3M
3.3, 33, 330, 3.3K, 33K, 330K, 3.3M
3.6, 36, 360, 3.6K, 36K, 360K, 3.6M
3.9, 39, 390, 3.9K, 39K, 390K, 3.9M
4.3, 43, 430, 4.3K, 43K, 430K, 4.3M
4.7, 47, 470, 4.7K, 47K, 470K, 4.7M
5.1, 51, 510, 5.1K, 51K, 510K, 5.1M
5.6, 56, 560, 5.6K, 56K, 560K, 5.6M
6.2, 62, 620, 6.2K, 62K, 620K, 6.2M
6.8, 68, 680, 6.8K, 68K, 680K, 6.8M
7.5, 75, 750, 7.5K, 75K, 750K, 7.5M
8.2, 82, 820, 8.2K, 82K, 820K, 8.2M
9.1, 91, 910,. 9.1K. 91K, 910K
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 79mm
• Connector type: SMA male
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male
This antenna is designed for LoRa modules based on 868MHz frequency (Europe). It is soldered on a hole in PCBs and has a significantly better sensitivity compared to ordinary wire.
• Frequency range: 868MHz
• Impedance: 50ohm
• Diameter: 5mm
• Lenght (spiral): 14mm
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
USB type C female connector for PCBs. This connector allows only power but not communication.