Components

This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.

This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.

This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.

USB type C female connector for PCBs. This connector allows only power but not communication.

Generic P-channel MOSFET transistor in TO-220 package. Generic implies that the exact part number may vary, but the transistor will always be equal to or better than the parameters below.

• Id: -23A
• Vgs(th): -2.0V
• Vdds: -100V
• Rds(on): 0.117ohm
• Package: TO-220
• Component example: IRF9540N

WiFi antenna with standard SMA male connector for connecting to your PCBs.

• Connector: SMA male
• Impedance: 50 ohm
• Frequency: 2.4GHz
• Dimensions: 50.5 x 19 x 10mm

GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.

This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.

• Frequency: 4GHz/LTE
• Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm

If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.

IPX SMD connector for soldering to the printed circuit board. It is most commonly used with antennas, and the impedance is 50 ohms.

If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.

SPST (single-pole, single-throw) is a simple switch that connects or disconnects the two contacts in its casing.

• Type: SPST
• Shape: box
• Max. current/voltage: 250VAC 10A
• Dimensions: 17mm x 13mm x 11mm (without contacts)

SPST (single-pole, single-throw) is a simple switch that connects or disconnects the two contacts in its casing.

• Type: SPST
• Shape: elongated
• Max. current/voltage: 250VAC 10A

Generic P-channel MOSFET transistor in DPAK package. Generic implies that the exact part number may vary, but the transistor will always be equal to or better than the parameters below.

• Vdss: -30V
• Vgs: -2.1V
• Rds(on): 0.068ohm
• Id: -30A
• Package: DPAK
• Components example: HY19P03

M4 rectifying diode inside SMAF package. Often used to adjust voltage and protect against reversed polarity.

SPDT (single-pole, dual-throw) is simple switch which connects central contact with one of the other two contacts located inside its housing.

The CH340G is USB to UART bridge that gains most of its popularity due to its extremely low price. Made in China and found on most Chinese versions of Arduino. The advantage of the C version is that it does not need an external oscillator.

• Package: SSOP20

JST (more specifically JST PH) connectors are nowadays the most common connectors for rechargeable lithium batteries, but they are also used for many other applications where fast, easy and favorable connection is required.

The transparent cover is detachable and is held by four Phillips screws. Between the cover and the base, it is possible to place a rubber band that would waterproof the box (rubber band included). The transparent cover is convenient, because it allows you to see inside the box or can be used with light sensors/UV lights.

Waterproof box with non-transparent cover for projects. The cover is detachable and is held by four Phillips screws. The box is waterproof and between the cover and the box, there can be placed a rubber band that would make the box safe from water.

• Dimensions: 115 x 90 x 55 mm

Caps for THT potentiometer from our store that would make control much easier and would simply just look better.

A 1M variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.

A 100k variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.

10 segment LED indicator derivates from classical 7-segment LED display and it enables staggered display. It can be used for various purposes, such as battery level indicator. It has 10 bars in total which which glow in red color.

• LED color: red
• Voltage: 3.3V
• Dimensions: 25.4 x 10.1 x 7.9 mm