easyC Cables & Adapters

In this category you can find all the cables, adapters you may need to use the easyC connection and communication system.

Showing all 13 results

Sort by:
Proto:bit
Proto:bit

Proto:bit allows you to access all micro:bit pins. Connect it to breadboard or use cables to connect additional components to it. Also comes with 2 easyC connectors that allow you to easily connect additional I2C sensors, breakouts and actuators.

Out of stock Raspberry Pi breadboard breakout + cable
Raspberry Pi breadboard breakout + cable

With the Raspberry Pi breadboard breakout board, you can easily connect your Raspberry Pi with a regular breadboard. It fits on standard half-size and full-size breadboards. It even adds a couple of ground and power supply pins. Best of all, the pins are already soldered. You just have to plug the cable in. This breakout will get you prototyping on the Raspberry Pi in no time!

 

Product usage tips:

The breakout board is compatible with Raspberry Pi that comes with 40-pin connector. It comes with a HAT ribbon cable for the Raspberry Pi. It has an easyC port for easier connection with other I2C breakout boards.

 

If the breakout board is not working properly, it’s likely not connected correctly. Check the pinout and the wiring. The culprit might be there. If that’s not the case, check if the HAT ribbon cable is connected as it should be. It should be straight and go to the bottom of the pins.

easyC Hub
easyC Hub

We made the easyC system for faster prototyping and easy connection between the components. However, some of the components have only one easyC port or you just want your cable managmenet made better. What to do in those cases? The easyC hub comes to the rescue! It has six connectors so you can easily expand your circuit. It’s as simple of a device as it can get.

 

Product usage tips:

You can connect easyC devices to the hub like you would to any other easyC device. Just plug the preferred easyC cable into the hub and a device you’re working with. That’s all there is to it.

 

You should avoid working with the hub in wet environments to ensure it lasts a long time. Be sure to watch the operating voltage of your circuit. Since the hub works on 3.3V, higher voltages can burn it and render it useless. There is a hole in the middle of the board so it can be secured to any surface.

Raspberry Pi easyC adapter
Raspberry Pi easyC adapter

This adapter makes it easy to connect easyC devices and sensors to the Raspberry Pi. It has 3 pieces of easyC connectors and a female header for Raspberry Pi, next to the header there are pins for connecting 5V and 3.3V and ground pins. It simply connects to the Raspberry Pi because its pinout matches the pinout of the Raspberry Pi.

easyC adapter
easyC adapter

Do you have an old I2C board lying around that would be perfect only if it had easyC connectors? With the easyC adapter and a little bit of soldering, you can give it new life. It will be able to connect easily to newer boards with easyC cables.

 

The adapter has two easyC connection ports and four plated through-holes: SCL, SDA, 3.3V, and GND. It comes with pins that need to be soldered to the board.

 

Product usage tips:

Connecting easyC devices to the adapter is the same as to any other easyC device. Choose an easyC cable and connect it to the adapter. That’s it.

 

To ensure the longevity of the adapter, avoid working with it in wet environments. Device operates at the 3.3V voltage level so higher voltages can burn it.

easyC cable with female headers
easyC cable with female headers

This easyC cable exposes all the pins on the easyC connector. Using this cable, any easyC board can be connected to an experimental board or vice versa.

Raspberry Pi easyC adapter
Raspberry Pi easyC adapter

This adapter makes it easy to connect easyC devices and sensors to the Raspberry Pi. It has 2 soldered easyC male connectors and a female header for Raspberry Pi, next to the header there are pins for connecting 5V and 3.3V and ground pins. It simply connects to the Raspberry Pi because its pinout matches the pinout of the Raspberry Pi.

easyC cable 50cm
easyC cable 50cm

easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.

This product is easyC compatible cable, with easyC connectors on both sides lenght 50cm.

easyC cable 20cm
easyC cable 20cm

easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.

This product is easyC compatible cable, with easyC connectors on both sides lenght 20cm.

easyC cable 10cm
easyC cable 10cm

easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.

This product is easyC compatible cable, with easyC connectors on both sides lenght 10cm.

easyC cable 6cm
easyC cable 6cm

easyC is the system for simple connection of microcontroller boards, sensors, and actuators which allows fast prototyping without the possibility of error. The connection between modules occurs with simple and pre-assembled cables, and easyC modules have connectors corresponding to the cables. easyC is based on the I2C communication.

This product is easyC compatible cable with easyC connectors on both ends. Cable lenght is 6cm.

easyC adapter
easyC adapter

This one is an adapter with easyC connectors for all older boards we’ve created without easyC connectors onboard.

easyC connector
easyC connector

easyC is a system developed by Soldered to establish easy connections between different I2C devices: microcontrollers, sensors, actuators. Connecting is easy and fast with pre-assembled cables. This connector is located on every easyC-compatible product.

items per page