Filter
Second filter
Third filter
Fourth filter

easyC ecosystem

Here you can find all cables, adapters and electronic devices that use the easyC connection system for connection and communication.

Showing 49–69 of 69 results

Sort by:
Hall effect sensor breakout with digital output & easyC
Hall effect sensor breakout with digital output & easyC

The hall effect sensor (Hall Effect sensor) will be able to detect the magnetic field in its vicinity thanks to the aforementioned physical law. A magnetic field that can be created by a magnet, a current flowing through a conductor or some third source, the Hall effect sensor will recognize each.

 

 

This sensor has a programmed threshold at which it will change the state of its output signal, so it is a sensor with a digital output. Through the easyC connectors, it enables a simple connection with the microcontroller.

 

I2C multiplexer TCA9548A breakout
I2C multiplexer TCA9548A breakout

Have you ever found yourself wanting to connect more than one I2C device to a single controller and couldn’t because they have identical I2C addresses? There you have it, I2C multiplexer (I2C MUX) allows you to use up to 8 devices with the same address on the same bus! If we mention that TCA9548A, the IC on which this breakout is based, has three adjustable pins for the I2C address, which means a total of 8 possible addresses. We can reach 64 devices with the same address on the same bus. For example, it is possible to connect 64 BME680 sensors that are read by only one microcontroller.

 

This adapter is particularly practical because it enables multiplexing of easyC devices.

ADC 16-bit ADS1115 4-channel with PGA breakout
ADC 16-bit ADS1115 4-channel with PGA breakout

ADC (Analog Digital Converter) is a device that reads analog signals (just like the analogRead () function in Arduino IDE) and converts them into a digital signal that can be read by a microcontroller. This breakout is based on the ADS1115 ADC, which reads values in 16-bit resolution, receives a maximum of 3.3V on its inputs and has a total of 4 channels (which can also be used as two differential). Works great with each microcontroller at 5V. It has 2 easyC connectors for easier connection on I2C communication.

IO expander MCP23017 breakout
IO expander MCP23017 breakout

Are you short on IO pins? Looking to increase the number of them? That’s what the GPIO Expander MCP23017 is for! It uses I2C communication to do so. With just two wires, 16 new fully configurable digital IO pins are added to a microcontroller.

 

Due to the jumpers on the board, the I2C address of a device can be changed. Thus, eight breakout boards can be connected to a microcontroller. All of the pins on the expander board have pull-out resistors that can be turned on and off.

Slider potentiometer breakout with easyC
Slider potentiometer breakout with easyC

Potentiometers are well known all around, and the sliding potentiometer is just one of its versions. You’ve probably seen it in some music equipment, and now you have the chance to add it to your project!

 

This board has easyC connector. Thanks to easyC ecosystem, this board can be connected using off-the-shelf cables, without soldering. Controlling the is as simple as it gets, too.

Out of stock Alcohol, Ethanol sensor MQ3 breakout with easyC
Alcohol, Ethanol sensor MQ3 breakout with easyC

MQ sensors, including the MQ3 sensor, have the capability to detect various gases. The MQ3 sensor is specifically designed to detect alcohol vapors. This means it is sensitive to alcohols such as methanol, ethanol, and isopropanol. The MQ3 sensor is commonly used for measuring alcohol concentration in the air and serves as a useful tool for alerting to the presence of alcohol in the environment.

It is important to note that MQ sensors are not specific to only one gas and can react to other gases besides the ones they are specifically designed for. Therefore, it is important to use the MQ3 sensor exclusively for alcohol detection and follow the manufacturer’s instructions to achieve optimal accuracy and reliability of measurements. It requires a short time to heat up in order to work correctly.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Ammonia sensor MQ137 breakout with easyC
Ammonia sensor MQ137 breakout with easyC

The sensitivity and selectivity of the MQ137 sensor allow it to effectively detect and measure levels of ammonia, making it a valuable tool for applications such as gas leakage detection, agricultural monitoring, and environmental sensing. By integrating the MQ137 sensor with appropriate electronic circuits and microcontrollers like Dasduino, you can create systems that provide real-time monitoring and prompt alerts in the presence of hazardous ammonia concentrations. It requires a short time to heat up in order to work correctly.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock Benzene, Toluene, Acetone, Formaldehyde sensor MQ138 breakout with easyC
Benzene, Toluene, Acetone, Formaldehyde sensor MQ138 breakout with easyC

The MQ138 sensor is specifically designed to detect various gases, with a primary focus on air quality monitoring. While its main target gas is formaldehyde (HCHO), it is also sensitive to a range of other gases, including volatile organic compounds (VOCs) such as toluene, alcohol, acetone, and hydrogen, as well as other harmful gases commonly found in the environment. It requires a short time to heat up in order to work correctly.

The breakout board provides both digital and analog output through the easyC system. Sensor readings are obtained through the easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock CO sensor MQ7 breakout with easyC
CO sensor MQ7 breakout with easyC

The sensitivity and selectivity of the MQ7 sensor enable it to effectively detect and measure carbon monoxide levels, making it a crucial tool for applications such as gas leakage detection, security systems, and environmental monitoring. By integrating the MQ7 sensor with appropriate electronic circuits and microcontrollers like Dasduino, you can create systems that enable real-time monitoring and prompt alerts in the presence of hazardous CO concentrations. It requires a short time to warm up in order to work correctly.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock CO, flammable gasses sensor MQ9 breakout with easyC
CO, flammable gasses sensor MQ9 breakout with easyC

We are surrounded by invisible gases everywhere. Although we generally don’t have to worry about them, in certain circumstances they can be very flammable and dangerous. The MQ9 breakout detects carbon monoxide, methane, propane and other flammable gases so that the right measures can be taken in time. The sensor detects carbon monoxide at 10-1000 ppm and other flammable gases at 100-10000 ppm.

The breakout board provides digital and analog information via the easyC system. Sensor readings are obtained via easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock Butane, LPG & Smoke sensor MQ2 breakout with easyC
Butane, LPG & Smoke sensor MQ2 breakout with easyC

MQ sensors, including the MQ2 sensor, have the capability to detect various gases. The MQ2 sensor is specifically designed to detect combustible gases such as LPG (liquefied petroleum gas), butane, propane, methane, alcohol, hydrogen, and smoke. These gases are commonly found in residential, industrial, and automotive environments. The sensor’s sensitivity and responsiveness enable it to detect even trace amounts of these gases, making it a valuable tool for gas leakage detection, fire detection, and air quality monitoring. It takes a short time to heat up in order to work correctly.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Air quality sensor MQ135 breakout with easyC
Air quality sensor MQ135 breakout with easyC

The versatility of the MQ135 sensor allows for its use in applications such as indoor air quality monitoring, gas leakage detection, and environmental sensing. While its main target gas is carbon dioxide (CO2), it is also sensitive to various other gases, including volatile organic compounds (VOCs), alcohol vapors, benzene, smoke, and other harmful gases commonly found in the environment. By integrating the MQ135 sensor with appropriate electronic circuits and microcontrollers like Dasduino, you can create systems that enable real-time monitoring and analysis of gas concentrations, allowing you to take necessary actions to maintain a healthy and safe environment.

The MQ135 air quality measurement module operates at 5V and consumes approximately 150mA. It requires some time to heat up before it can provide accurate results.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

LPG, Butane sensor MQ6 breakout with easyC
LPG, Butane sensor MQ6 breakout with easyC

Humans can detect many smells, but may have difficulty distinguishing gases. That’s why we use sensors like the MQ6 that detects LPG and butane in the air. When heated to the optimal operating temperature, it very quickly detects changes in air concentration between 200 and 10,000 ppm.

The breakout board provides digital and analog information via the easyC system. Sensor readings are obtained via easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock Methane, CNG sensor MQ4 breakout with easyC
Methane, CNG sensor MQ4 breakout with easyC

Have you ever wondered how much natural gas and methane are present in your living room? You can easily measure it! The MQ4 breakout board is a user-friendly sensor that detects natural gas and methane (CH4) in the air. Once it reaches operating temperature, it quickly detects changes in air concentration within the range of 200 to 10,000 ppm.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Ozone sensor MQ131 breakout with easyC
Ozone sensor MQ131 breakout with easyC

The sensitivity and selectivity of the MQ131 sensor enable it to effectively detect and measure ozone levels, making it a valuable tool for applications such as air quality monitoring, ozone generators, and ozone leakage detection systems. By integrating the MQ131 sensor with appropriate electronic circuits and microcontrollers like Dasduino, you can create systems that enable real-time monitoring of ozone concentration and trigger alerts when dangerous levels are detected.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Obstacle sensor with easyC
Obstacle sensor with easyC

The TCRT5000 is an infrared (IR) reflective sensor module that is commonly used for proximity sensing and line-following applications. It consists of an infrared emitter and a phototransistor placed side by side in a compact package. The emitter emits infrared light, which gets reflected off nearby objects, and the phototransistor detects the intensity of the reflected light.

This sensor module is widely used in robotics and automation projects. It can be used to detect the presence or absence of objects by measuring the intensity of reflected infrared light. It is also commonly employed in line-following robots where it can detect and follow lines marked with contrasting colors.

The TCRT5000 operates on a supply voltage typically ranging from 3.3V to 5V. The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

Two mounting holes enable easy mounting to surfaces.

 

Out of stock Natural gas, LPG sensor MQ5 breakout with easyC
Natural gas, LPG sensor MQ5 breakout with easyC

Is your office located near a high traffic area? Are you concerned about the presence of natural and liquefied petroleum gases in your work environment? The MQ series sensors can help detect various gases, and the MQ5 sensor is an easy-to-use sensor that provides information about the levels of natural gases and LPG (liquefied petroleum gas) in your surroundings. It quickly detects gas particles in the range of 200 to 10,000 ppm.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

Out of stock Hydrogen sensor MQ8 breakout with easyC
Hydrogen sensor MQ8 breakout with easyC

Hydrogen is all around us, and it is dangerous because it is highly flammable. Its leakage can be very dangerous for both life and property. That is why it is important to detect any leakage to prevent such losses in the industry. To do this, hydrogen sensors such as the MQ8 breakout board are used. The sensor detects hydrogen in the range of 100-1000 ppm.

The breakout board provides digital and analog information via the easyC system. Sensor readings are obtained via easyC.

 

Product usage tips:

 

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

easyC adapter
easyC adapter

This one is an adapter with easyC connectors for all older boards we’ve created without easyC connectors onboard.

Ultrasonic sensor with easyC
Ultrasonic sensor with easyC

The HC-SR04 ultrasonic sensor is an affordable and super-popular sensor that measures the distance between itself and an object located in front of the sensor. Very simple to use, it returns the distance in centimeters or inches.

In this variation, it comes on a board with an Attiny microcontroller that sends readings from the sensor as a digital signal via the easyC connector to the microcontroller, which makes its connections a piece of cake.

items per page