In this category, you can find all products from the offer that are on sale.
To claim an additional 30% discount, enter “SALE30” in the coupon field on the shopping cart page.
Showing 25–48 of 203 results
A load cell is a small device that is able to weigh the load that is on it. Depending on the load, it provides very small output voltages that need to be amplified (e.g. using an op-amp or an ADC with a built-in op-amp) in order to be able to do useful things with it. It has two fixed and two variable resistors connected to the Wheatstone bridge.
It needs to be connected to the HX711 board so you can read the readings with the Dasduino. For more details, see How to Use the Module Tutorial in the upper right corner.
A loadcell is a small device that is able to weigh the load that is on it. Depending on the load, it provides very small output voltages that needs to be amplified (e.g. using an op-amp or an ADC with a built-in op-amp) in order to be able to do useful things with it. It has two fixed and two variable resistors connected to the Wheatstone bridge.
It needs to be connected to the HX711 board so you can read the readings with the Croduino. For more details, see How to Use the Module Tutorial in the upper right corner.
Crystal (oscillator) with a frequency of 16MHz.
7805 is often used 5V linear regulator, in this version of Through Hole (THT). It can only provide 100mA current at 5A it carefully used. Be sure to add the output decoupling capacitors.
RV24YN20S Potentiometer with variable resistance of 10k intended for housing installation. Comes with cap and dial. Carbon, usually used to adjust the speed of rotation of the motor on the inverter.
Large DPDT (Dual Pole Dual Throw) panel mount switch. Breaks two wires simultaneously.
The DIP switch is a small switch that is simply used with breadboard or protoboard.
• Number of poles: 2
• Pitch: (2.54mm)
The DIP switch is a small switch that is simply used with breadboard or protoboard.
• Number of poles: 5
• Pitch: (2.54mm)
This antenna is designed for LoRa modules based on 868MHz frequency (Europe).
• Frequency range: 868MHz (Europe)
• Impedance: 50ohm
• Lenght: 110mm
• Connector type: SMA male
If you have a device that you want to connect to WiFi and want to use an IPX connector, then all you need is this antenna. Simply connect it to the IPX connector and your device is ready to connect to your WiFi network. This product features 2.4G/5G connection.
A socket for standard 8-pin DIL integrated circuit.
Micro-USB SMD connector for soldering to the printed circuit board. The same as it’s used to Croduino Nova, CP2102 USB to UART adapter.
3mm diffused LEDs are great for trying out and experimenting with LEDs.
Are you repairing or developing electronic boards? This set of capacitors is incredibly useful because you will never have to think again if you have that specific capacitor. It consists of 80 different values each of which comes in an amount of 50 pieces.
• Package: 0402
• 50 pcs of 80 values= 4000 pcs
• Capacity values [F]:
0.5pF, 2.7pF, 7.5pF, 24pF, 82pF, 1nF, 68nF
0.75pF, 3pF, 8pF, 27pF, 100pF, 1.5nF, 82nF
1pF, 3.3pF, 8.2pF, 30pF, 110pF, 2.2nF, 100nF
1.2pF, 3.6pF, 9pF, 33pF, 120pF, 3.3nF, 220nF
1.3pF, 3.9pF, 10pF, 36pF, 150pF, 4.7nF, 470nF
1.5pF, 4.3pF, 11pF, 39pF, 180pF, 6.8nF, 680nF
1.6pF, 4.7pF, 12pF, 43pF, 200pF, 8.2nF, 820nF
1.8pF, 5pF, 15pF, 47pF, 220pF, 10nF, 1uF
2pF, 6pF, 16pF, 51pF, 330pF, 15nF,
2.2pF, 6.2pF, 18pF, 56pF, 470pF, 22nF,
2.4pF, 6.8pF, 20pF, 62pF, 680pF, 33nF,
2.5pF, 7pF, 22pF, 68pF, 820pF, 47nF,
Waterproof box with non-transparent cover. The cover is detachable and is held by four Phillips screws. between the cover and the base, it is possible to place a rubber band that would achieve a waterproof of a box and a rubber band comes within a box. Box has four Phillips screws for mounting as shown on the pictures.
• Dimensions: 65 x 59 x 35 mm
The transparent cover is detachable and is held by four Phillips screws. Between the cover and the base, it is possible to place a rubber band that would waterproof the box (rubber band included). The transparent cover is convenient, because it allows you to see inside the box or can be used with light sensors/UV lights.
Are you repairing or developing electronic boards? This set of capacitors is incredibly useful because you will never have to think again if you have that specific capacitor. It consists of 90 different values each of which comes in an amount of 50 pieces.
• Package: 0402
• 50 pcs of 90 values = 4500 pcs
• Capacity value [F]:
0.5pF, 3.3pF, 7pF, 20pF, 62pF, 200pF, 2.2nF, 100nF
0.75pF, 3.6pF, 7.5pF, 22pF, 68pF, 220pF, 3.3nF, 220nF
1pF, 3.9pF, 8pF, 24pF, 75pF, 270pF, 4.7nF, 470nF
1.2pF, 4pF, 8.2pF, 27pF, 82pF, 330pF, 6.8nF, 680nF
1.5pF, 4.3pF, 9.1pF, 30pF, 91pF, 390pF, 8.2nF, 1uF
1.8pF, 4.7pF, 10pF, 33pF, 100pF, 470pF, 10nF, 2.2uF
2pF, 5pF, 11pF, 36pF, 110pF, 560pF, 15nF,
2.2pF, 5.1pF, 12pF, 39pF, 120pF, 680pF, 22nF,
2.4pF, 5.6pF, 13pF, 43pF, 130pF, 820pF, 33nF,
2.5pF, 6pF, 15pF, 47pF, 150pF, 1nF, 47nF,
2.7pF, 6.2pF, 16pF, 51pF, 160pF, 1.2nF, 68nF,
3pF, 6.8pF, 18pF, 56pF, 180pF, 1.5nF, 82nF,
Waterproof box with non-transparent cover for projects. The cover is detachable on a snap mechanism it is not held by any screws. However the specs of the manufacturer we do not recommend this box to be used outside.
• Dimensions: 100 x 60 x 25 mm
Waterproof box with non-transparent cover for projects. The cover is detachable and is held by four Phillips screws. The box is waterproof and between the cover and the box, there can be placed a rubber band that would make the box safe from water.
• Dimensions: 115 x 90 x 55 mm
Waterproof box with transparent cover. The cover is detachable and is held by four Phillips screws. Between the cover and a box, it is possible to place a rubber band that would achieve the box to be waterproof, the rubber band comes within the box. A transparent cover is convenient because you can see inside or can be used with light sensors/UV rays.
• Dimensions: 158 x 90 x 60 mm
10 segment LED indicator derivates from classical 7-segment LED display and it enables staggered display. It can be used for various purposes, such as battery level indicator. It has 10 levels in total which glow in different colors.
• LED color: 4-color (2x red, 3x yellow, 4x green, 1x blue)
• Voltage: 3.3V
• Dimensions: 25.4 x 10.1 x 7.9 mm
The relay 12v coil is a device used to turn (overlapping) large loads – those that require higher voltages or currents. These relays are used on the modules with the relay. There are NO and NC pins.
• Current needed for activation: 77mA
• Coil voltage: 12V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A
Large LED diode with 10mm diameter.
Large LED diode with 10mm diameter.