Filter
Second filter
Third filter
Fourth filter

Input devices

This category includes input devices such as joystick module, membrane keyboards, cameras, fingerprint sensor, slider potentiometer etc.

Showing all 13 results

Sort by:
Membrane keyboard 4x4
Membrane keyboard 4x4

The membrane keyboard is a system of 16 keys that are mutually connected and enable us more complex entry to Dasduino/Arduino. Using this keyboard, you can create whole systems of menus, data input, and adjustment of different parameters.

Joystick 2-axis with pushbutton breakout
Joystick 2-axis with pushbutton breakout

Joystick module is well known to all – it is identical to the one found in the PlayStation2 joystick. Whether you are making a game with a microcontroller or want more freedom while navigating a joystick module will come handy.

It reads X and Y position of the joystick knob (used for controlling) and whether the joystick is being pressed down. X and Y values are shown in the form of analog values while reading off if the joystick is pressed or not is shown in the form of digital value (HIGH/LOW; it has pull-up resistor).

ADC 12-bit ADS1015 4-channel with PGA breakout
ADC 12-bit ADS1015 4-channel with PGA breakout

ADC (Analog Digital Converter) is a device that reads analog signals (just like the analogRead () function in Arduino IDE) and converts them into digital signals that can be read by a microcontroller. This breakout is based on the ADS1015 ADC, which reads values in 12-bit resolution, receives a maximum of 3.3V on its inputs and has a total of 4 channels (which can also be used as two differential). Works great with any microcontroller at 5V. It has 2 easyC connectors for easier connection on I2C communication.

Slider potentiometer breakout
Slider potentiometer breakout

Potentiometers are well known all around, and the sliding potentiometer is just one of its versions. You’ve probably seen it in some music equipment, and now you have the chance to add it to your project!

 

• Type: linear
• Resistance: 10k
• Dimensions: 86 x 22 mm

Out of stock CMOS camera module w/ OV7670
CMOS camera module w/ OV7670

Although many do not know, there is a camera that can work with Arduino / Croduino. It is a CMOS camera, with VGA quality images that are connected to Croduino via I2C. Now it’s your turn to think of the application! Maybe combine with a motion sensor that could be activated if you someone entered the room?

 

ADC 16-bit ADS1115 4-channel with PGA breakout
ADC 16-bit ADS1115 4-channel with PGA breakout

ADC (Analog Digital Converter) is a device that reads analog signals (just like the analogRead () function in Arduino IDE) and converts them into a digital signal that can be read by a microcontroller. This breakout is based on the ADS1115 ADC, which reads values in 16-bit resolution, receives a maximum of 3.3V on its inputs and has a total of 4 channels (which can also be used as two differential). Works great with each microcontroller at 5V. It has 2 easyC connectors for easier connection on I2C communication.

Matrix keyboard 3x4
Matrix keyboard 3x4

Matrix keyboard is a system of 12 buttons that are interconnected that allowes us a more complex data input on Croduino/Arduino. With this keyboard you will create whole systems of menus, data entry and settings of various parameters.

Dimensions: 70 x 50 mm

Out of stock IO expander MCP23017 breakout
IO expander MCP23017 breakout

Are you short on IO pins? Looking to increase the number of them? That’s what the GPIO Expander MCP23017 is for! It uses I2C communication to do so. With just two wires, 16 new fully configurable digital IO pins are added to a microcontroller.

 

Due to the jumpers on the board, the I2C address of a device can be changed. Thus, eight breakout boards can be connected to a microcontroller. All of the pins on the expander board have pull-out resistors that can be turned on and off.

Matrix keyboard 4x4
Matrix keyboard 4x4

The Matrix Keyboard is a system of 16 keys that are interconnected, allowing us to provide more complex data input to the Croduino / Arduino. With this keyboard you will create whole systems of menus, data entry and settings of various parameters.

Dimension: 68 x 65 mm

Out of stock Membrane keyboard 1x1
Membrane keyboard 1x1

A mini version of our larger membrane keyboard that will still be sufficient for projects that need slightly less input.

 

  • The size of the upper part: xcm x xcm
  • Cable lenght: 9cm, flexible
  • Connector: 5-pin
Emergency stop button
Emergency stop button

All real machines have an emergency stop button when pressed the whole machine stops. It can be very useful in case of the danger of someone working on that machine. If you want to install a similar thing on your project, here it is!

Type: DPST
Maximal voltage: 660V
Maximal current: 10A
Button diameter: 40mm
Mounting hole diameter: 22mm
• Dimensions: 60 x 70mm

Out of stock Membrane keyboard 1x4
Membrane keyboard 1x4

Mini version of our larger membrane keyboard that will sometimes still be sufficient for projects that need a few inputs.

 

Out of stock Fingerprint sensor adapter
Fingerprint sensor adapter

This adapter will help you connect our fingerprint sensor with ease.

items per page