Here you can find all the chemical products we offer. For example compressed air in spray, PCB cleaning solution, lubricants etc.
Showing 1–24 of 26 results
Isopropyl alcohol is an alcohol of high purity which can be found in almost every workshop. It is useful for cleaning printed circuit boards, because it evaporates quickly and allows the removal of greasy deposits (such as traces of flux/paste) and dirt. It is also used in 3D printer cleaners and all other applications where cleanliness is important. NOTE: it also has antibacterial properties.
Sodium persulfate is a chemical compound used to etch printed circuit boards. Printed boards (usually FR1 and FR4 materials are used) contain laminated copper. This chemical will remove it in places where it is not covered (usually it is covered with toner transfer, lightening, or with various colors). For the etching process, it is necessary to dissolve 250g of sodium persulfate in 1 liter of water, by adding the powder to the water, not the other way around. The solution will flood when it is saturated.
• Weight: 500g
• Neutral odor, easily soluble in waterHeating the solution to 50C speeds up the etching process
•
• Keep it tightly closed and out of reach of children. In case of contact with skin or eyes, rinse immediately with plenty of water and seek medical advice.
Vaseline oil is used to lubricate mechanical parts and precision mechanisms in all industries. It leaves no traces, has no odor or color and does not adversely affect plastics.
• Package: 100mL
Silicone-based viscous oil that will reach even the most inaccessible places. It has high insulating properties and eliminates all types of unwanted currents, which makes it suitable for use in electronics.
• Package: 100mL
Thermally conductive paste is used at the points of contact of two metals where thermal conductivity is required. It is most often some type of heatsink, either for the processor or any other type of electronic component. The base of this thermally conductive paste is silicone, and steel dust is added to it, which achieves thermal conductivity.
• Weight: 100g
• Thermal conductivity: >6W/mK
Kontakt S is used to remove oxides and sulfides from electrical contacts and it protects against corrosion. This ensures a smooth flow of current through the connector, even in cases of already oxidized and worn contacts. It is especially useful in audio products, where the cleanliness of the contact is crucial.
• Package: 400mL
• Spray
• Density: 0,74g/cm3
Isopropyl alcohol is a high purity alcohol that can often be found in every workshop. It is useful for cleaning printed circuit boards because it evaporates quickly, and allows the removal of fatty deposits (such as traces of flux and paste) and dirt. It is also used with 3D printers to clean the print substrate and for all other applications where cleanliness is sought. It is important to note that it has antibacterial action.
• Package: 250mL
• Dispersion:spray
• Purity: 96%
Kontakt U spray is a mixture of a substance used to clean filled electronic boards and electrical contacts. Removes grease, dust, oils, silicones, sulfides and oxides, as well as all residues after soldering (including rosin and flux).
• Package: 400mL
• Density: 0,74g/cm3
Isopropyl alcohol is a high purity alcohol that can often be found in every workshop. It is useful for cleaning printed circuit boards because it evaporates quickly and removes grease deposits (such as flux or paste traces) and other impurities. It is also used with 3D printers to clean the print surface and for all other applications where purity is required. It is important to note that it is antibacterial.
• Packaging: 300mL
• Dispersion: syringe
• Purity: 96%
Printed boards during soldering and various repairs very often remain dirty from flux and other impurities. To avoid gradual degradation of solder quality, oxidation, and potential short circuits, the tiles need to be cleaned. This spray will help significantly here, and the brush that comes with the spray will further help remove dirt mechanically.
• Package: 400mL
Isopropyl wipes are used to clean various surfaces and they work especially well against substances for which alcohol is a solvent. In electronics they will be useful for cleaning flux residues and solder paste.
• Material: fabric
• Dimensions of the wipe: 160 x 125mm
• Soaked with 99,9% isopropyl alcohol
• Quantity: 25pcs
Isopropyl alcohol is a high purity alcohol that can often be found in every workshop. It is useful for cleaning printed circuit boards because it evaporates quickly and removes grease deposits (such as flux or paste traces) and other impurities. It is also used with 3D printers to clean the print surface and for all other applications where purity is required. It is important to note that it is antibacterial.
• Package: 500mL
• Purity: 96%
Ceramic-based lubricant is often used for mechanical parts that is under constant heavy load. It has an extremely large temperature range,which is why it can also be used in owen. It does not contain metals or silicone, and is resistant to chemicals, water and all weather conditions.
• Package: 100mL
• Temperature range: -50 – 1200°C
Graphite-based lubricant contains carefully added additives that extend shelf life and load resistance. It is also water resistant.
• Package: 100mL
• Temperature range for use: -20 – 50°C
Compressed air is most commonly used for cleaning electronics. Since the gas from the container comes out under high pressure, it is perfect for cleaning dust and all particles. It is colorless, odorless and leaves no traces. It is able to reach even the most inaccessible parts of any electronic equipment and is especially practical for cleaning places you don’t want to touch.
• Package: 300mL
Also known as flux varnish, this spray flux protects printed circuit boards from oxidation and corrosion during storage. This enables better and faster soldering, because it contains flux, and also prevents cold solders. Since it is in the form of a spray, application is extremely easy.
Copper-based lubricant is intended for lubrication of all types of mechanical joints that work at extremely high temperatures which makes it suitable for use in owen.
• Package: 100mL
• Temperature range: -40 – 1100°C
This lubricant is specially developed for use with all types of threads. It ensures that the threads will remain protected from oxidation and rust in the long run and prevents them from seizure of metal part, thus enabling very easy assembly and disassembly after application. It works in conditions of higher humidity, higher pressure and higher temperature. Water resistant and adheres very well to metal surfaces.
• Package: 100mL
This lubricant contains molybdenum disulfide which has a very low frictional resistance. It is used for metal parts and prevents them from collapsing and wearing out. It is very often used to lubricate parts of heavy industrial equipment, such as forklifts or cranes. For application at temperatures up to 150C.
• Temperature : -30 – 150C
• Package: 100mL
These wipes are intended for cleaning consumer electronics that are used every day: monitors, mouse, keyboard, laptop, all types of laboratory equipment such as a multimeter, oscilloscope, power supply, etc..
• Quantity: 24
Photo lacquer developer for making printed circuit boards by photo process.
• Weight: 22g
• Does not contain NaOH
Thermal conductivity is a property often required in cases where two metals are in contact. One of them needs to be cooled, while the other is most often a refrigerator. Although thermal paste is a logical choice in this case, thermally conductive adhesive will be particularly useful in some cases, especially when the joint is under mechanical stress. This adhesive is often used in electronics to attach temperature sensors, coolers and el. components and LEDs..
• Weight: 10g
• Operating temperature: -50 – 200°C
• Thermal conductivity: 2W/mK
• Drying time: 5min do 2
4h
Instructions for use:
• The surface must be cleaned before applying the adhesive
• Apply the glue thinly, not thicker than 6mm
• Use the glue 12 months after opening
Thermally conductive paste is used at the points of contact of two metals where thermal conductivity is required. It is most often some type of heatsink, either for the processor or any other type of electronic component. The base of this thermally conductive paste is silicone, and diamond dust is added to it in a percentage of 10% to increase the thermal conductivity. Comes with a special application brush.
• Mass: 4g
• Thermal conductivityt: >4W/mK
Isopropyl alcohol is a high purity alcohol that can often be found in every workshop. It is useful for cleaning printed circuit boards because it evaporates quickly and removes grease deposits (such as flux or paste traces) and other impurities. It is also used with 3D printers to clean the print surface and for all other applications where purity is required. It is important to note that it is antibacterial.
• Packaging: 5L
• Purity: 96%