Handtools

Classic and simple cutting pliers for cutting off excess material after soldering. Those can also be used for wire cutting or insulation removing.

Once you learn how to solder, you notice that your soldering isn’t perfect. Desoldering pump is a tool that should be on the table of each maker/electronics engineer because it allows easy removal of excess solder, thus repairing short circuits or removing the components from the board. It works on the principle of “sucking in” the solder (liquid state) inside itself. It is completely safe to use.

This set of screwdrivers and accessories for working with electronics contains everything you will need when repairing electronics. See the full list below, the set consists of a screwdriver, tweezers, an opening tool, a cutting knife and several opening levers.

• Screwdrivers: Torx 0.8x40mm, T3x40mm, T4x40mm, T5x40mm, T6x40mm, flat 2.0x40mm, philips 1.5x40mm, philips 2.0x40mm
• Cutting knife (traces)
• 2 tweezers
• Opening levers: 2 plastic triangle shaped, 2 plastic levers, 1 metal lever

ESD (ElectroStatic Discharge) or static electricity is a phenomenon where electricity flows suddenly between two electrically charged objects that are in touch or near each other. You experienced it, most likely,  when you touched something and felt “current” hurting you. Other than being unpleasant, there are no major consequences caused by ESD. But in electronics, ESD is very dangerous and can destroy your components and semiconductors.

This is where antistatic bracelet helps. If its other end is properly terminated to ground, it means that you are too. Through the 1M resistor, current flows to ground where it safely “goes” without being felt, and there won’t be any damage to components. It is always recommended to wear an anti-tatic bracelet whilte working with electronics.

A vernier caliper is a tool that allows precise measurements of many physical dimensions. This one, made of high-strength stainless steel and with a digital display of the measured value.

To pick up ultra-small components and put them in the right place you simply need to have the right tools. One such are tweezers for SMD components, which will allow you to handle even 0603 components and with a little practice, even smaller ones. Of course, tweezers are ESD safe so you don’t have to worry that something will happen to your components. This set consists of 6 tweezers with which you will be able to place all types of SMD components.

• Number of tweezers inside set: 6

This product contains 9 most commonly used Allen keys in a practical holder. At the end of each Allen key there is a hex head that allows you to tighten the Allen screws from any angle, which can be extremely useful on screws in inaccessible areas.

• Set contains Allen keys of sizes: 1.5, 2, 2.5, 3, 4, 5, 6, 7, 10
• Material: CrV steel

Classic pliers for precise cutting of the legs after soldering or for cutting the wire and removing the insulation.

To pick up ultra-small components and put them in the right place you simply have to own a right tool. One such are the tweezers for SMD components which will enable you to handle 0603 components. With little more exercise even smaller ones, won’t be an issue. Of course, the tweezers are ESD safe so you shouldn’t worry that something will happen to your components.

Hex key for standard 2mm head.

• Material: Steel(CrV)
• For 2mm hex heads

Every household, let alone a workshop, is not complete without an AC tester. This affordable tester allows you to check for AC voltage in the wires.

Classic small pliers as a basic tool of every electronic workshop. It will come in handy for bending components, cutting or just holding.

Cutting knife is actually a sharp scalpel that you can operate very precisely. It will be very useful for cutting faulty traces on printed circuit boards, but also for any other purpose of precision cutting or marking.

• Material: steel

A vernier caliper is a tool that allows precise measurements of many physical dimensions. This one, made of high-strength stainless steel and with a digital display of the measured value, will last you a lifetime. It comes in a practical plastic box for storage.

The SMD components are very small and the tweezers help us to do the job properly. And what should we do when we are having larger components, such as integrated circuits that can be so large that we can not grab them with tweezers? SMD vacuum tweezer will help us here. It uses a vacuum to grab the surface of IC. The vacuum is activated by pressing a small button, so using this tool won’t be a problem. It comes with several tips for different integrated circuits.

Classic power adapter which converts other power connectors to EU schuko power connector