Filter
Second filter
Third filter
Fourth filter

Tools & Lab equipment

In this category you can find everything you need for your small electronic laboratory. For example, cleaning chemicals, multimeters, connectors, etc.

Showing 25–48 of 123 results

Sort by:
Desoldering pump
Desoldering pump

Once you learn how to solder, you notice that your soldering isn’t perfect. Desoldering pump is a tool that should be on the table of each maker/electronics engineer because it allows easy removal of excess solder, thus repairing short circuits or removing the components from the board. It works on the principle of “sucking in” the solder (liquid state) inside itself. It is completely safe to use.

Cleaning net for soldering iron
Cleaning net for soldering iron

If the soldering iron isn’t clean, neither will the the solder joint. This cleaning net allows quick tip cleaning by “stabbing” the soldering iron in it. When the net is filled with solder, simply remove it from the casing, clean the excess solder, return it back and use it again!

PCB breadboard/protoboard
PCB breadboard/protoboard

This PCB is also a protoboard. It offers both the simplicity and the functionality of a breadboard. It is the same size as the modular half-size breadboard and has the same connections to pins. The board allows you to make the temporary circuit from the breadboard permanent.

 

Product usage tips:

 

The board has three mounting holes for secure placement on different surfaces.

 

Set of screwdrivers and accessories for electronics
Set of screwdrivers and accessories for electronics

This set of screwdrivers and accessories for working with electronics contains everything you will need when repairing electronics. See the full list below, the set consists of a screwdriver, tweezers, an opening tool, a cutting knife and several opening levers.

 

Screwdrivers: Torx 0.8x40mm, T3x40mm, T4x40mm, T5x40mm, T6x40mm, flat 2.0x40mm, philips 1.5x40mm, philips 2.0x40mm
• Cutting knife (traces)
• 2 tweezers
• Opening levers
: 2 plastic triangle shaped, 2 plastic levers, 1 metal lever

Auxiliary arm for electronics
Auxiliary arm for electronics

The auxiliary arm is a practical desktop tool that allows you to hold PCBs, components, and wires when soldering or working with them. Thanks to the crocodile clips adjustable in all directions, you can attach any type of material and adjust it to an accessible position. The arm itself is heavy and will not move during work. In addition, the third arm, as it is also called, has a magnifier with LED lighting on it, so working with small components will be even easier. If that’s not enough, there is also a soldering iron holder on this auxiliary arm.

 

Number of crocodile clips: 2
• LED lighting powering: 3x AAA batteries

Multimeter probes
Multimeter probes

High-quality spare probes for a multimeter.

ESD antistatic bracelet
ESD antistatic bracelet

ESD (ElectroStatic Discharge) or static electricity is a phenomenon where electricity flows suddenly between two electrically charged objects that are in touch or near each other. You experienced it, most likely,  when you touched something and felt “current” hurting you. Other than being unpleasant, there are no major consequences caused by ESD. But in electronics, ESD is very dangerous and can destroy your components and semiconductors.

 

This is where antistatic bracelet helps. If its other end is properly terminated to ground, it means that you are too. Through the 1M resistor, current flows to ground where it safely “goes” without being felt, and there won’t be any damage to components. It is always recommended to wear an anti-tatic bracelet whilte working with electronics.

Digital multimeter
Digital multimeter

The multimeter, along with the soldering iron, is the basic tool of every electronics engineer. If you are a beginner, this multimeter will be enough for you to learn to measure various physical quantities related to electronics. Measure AC and DC voltage, AC and DC current, resistance, transistor gain, test diodes and conductivity – all with this multimeter. It comes with test cables, and you’ll only need 2 AAA batteries to get started. It also has a fuse to measure current, as a safety supplement.

If you are looking for a best buy multimeter for your workshop, to work for years (probably centuries) and give reliable readings, you have found it. The multimeter does not have automatic range detection, no backlight or frequency measurement, but it will measure DC voltage up to 1000V, AC voltage up to 750V, DC current up to 10A, capacity up to 100uF, resistance up to 200Mohm. It has a buzzer to conduct conductivity and it has an automatic shut-off.

 

• DC voltage measuring ranges: 200mV, 2V, 20V, 200V, 1000V
• AC voltage measuring ranges: 200mV, 2V, 20V, 200V, 750V
• DC current measurement ranges: 2mA, 20mA, 200mA, 10A
Capacity measurement areas: 20nF, 200nF, 2uF, 20uF, 200uF
• Resistance measurement areas: 200ohm, 2000ohm, 20kohm, 200kohm, 2Mohm, 20Mohm, 200Mohm
• Dimensions: 190 x 90mm

Desoldering wick, high-quality 1.9mm
Desoldering wick, high-quality 1.9mm

Desoldering wick is a very practical tool for every workshop. It’s a braided copper wire, soaked in flux, so it catches solder effectively. If you have a spot from which you need to remove the solder, this strip will do a great job. Unlike the discharge pump, this strip can completely remove the solder from a hole or a pad. 1.5m should last long since you spend only one or two centimeters per one desoldering.

 

Lenght: 1.5m
Width: 1.9mm

Vernier caliper
Vernier caliper

A vernier caliper is a tool that allows precise measurements of many physical dimensions. This one, made of high-strength stainless steel and with a digital display of the measured value.

Locker with 16 drawers 70x50x30mm
Locker with 16 drawers 70x50x30mm

A well-organized workshop is a very important thing. Is there a better way to save components than well-organized compartments? This cabinet comes with 16 transparent drawers ideal for storing electronic components. On the front of each drawer, there is a space where it’s possible to add a label.

 

Cabinet dimensions: 220 x 70 x 160 mm
Tray dimensions: 70 x 50 x 30 mm
Material: polypropylene and polystyrene
Number of drawers:16

ESD tweezers set for electronics
ESD tweezers set for electronics

To pick up ultra-small components and put them in the right place you simply need to have the right tools. One such are tweezers for SMD components, which will allow you to handle even 0603 components and with a little practice, even smaller ones. Of course, tweezers are ESD safe so you don’t have to worry that something will happen to your components. This set consists of 6 tweezers with which you will be able to place all types of SMD components.

 

• Number of tweezers inside set: 6

Hantek 6022BL USB osciloscope
Hantek 6022BL USB osciloscope

An oscilloscope is very useful to have nearby – it allows you to display signals depending on the time. Usual problem with oscilloscopes is that they are large and awkward to carry, but with this USB oscilloscope it is no longer a problem! Plug it into a USB port, install drivers and software, plug in the probes and measure. Using special software, you have controls over the device as on a classic desktop oscilloscope. It has 2 channels, measures up to 20MHz and takes 48 million samples per second. It comes with two probes.

 

If an analog approach to signal processing with an oscilloscope is not enough, (firmware developers, we hear you!) There is also a 16-channel logic analyzer. It will read signals from 0V to 5.5V on 16 channels simultaneously, displaying them on the timeline for easy analysis, so you can accurately measure the duration and decode each digital signal. The logic analyzer software even decodes the data being sent, if it is a standard communication. Comes with 16 quick signal connecting connectors.

 

Osciloscope
• Frequency range
: 20MHz
• Channels: 2
• Sample rate: 48MSa/s
• Memory depth: 1M
• Rise time: 17.5ns
• Time division: 1ns/div – 5000s/div
• Voltage division: 20mV/div – 5V/div

Logic analyzer
• Channels
: 16
• Input voltage range: 0V – 5.5V
• Maximum number of samples: 48M
• Frequency range: 10MHz
• Memory depth: 1M/CH

• Connection: USB
• Comes with s 2 PP80B probes
• Dimensions: 200 x 100 x 35mm
• Weight: 300g

Vaseline oil 100mL
Vaseline oil 100mL

Vaseline oil is used to lubricate mechanical parts and precision mechanisms in all industries. It leaves no traces, has no odor or color and does not adversely affect plastics.

 

Package: 100mL

Set of allen keys
Set of allen keys

This product contains 9 most commonly used Allen keys in a practical holder. At the end of each Allen key there is a hex head that allows you to tighten the Allen screws from any angle, which can be extremely useful on screws in inaccessible areas.

 

Set contains Allen keys of sizes: 1.5, 2, 2.5, 3, 4, 5, 6, 7, 10
• Material: CrV steel

Cutting pliers
Cutting pliers

Classic pliers for precise cutting of the legs after soldering or for cutting the wire and removing the insulation.

SMD tweezers ESD-12
SMD tweezers ESD-12

To pick up ultra-small components and put them in the right place you simply have to own a right tool. One such are the tweezers for SMD components which will enable you to handle 0603 components. With little more exercise even smaller ones, won’t be an issue. Of course, the tweezers are ESD safe so you shouldn’t worry that something will happen to your components.

Logic analyzer
Logic analyzer

A logic analyzer allows you to record and display a signal, usually a bus, on your computer screen in real time. It is powered via USB, and simultaneously records up to 8 channels. Cables are also included.

 

20x plastic container 100x56x125mm
20x plastic container 100x56x125mm

Workshop organization is very important, and what is better for storing components than well-organized containers? There are 20 of these containers in a package and they are ideal for storing electronic components. They are quite large, so you can store larger products. We use identical ones like this in our warehouses! On the front of each tray, there is a space where you can stick a label with the description of the component inside. The containers can be taken apart and put back together, so they can be used in various stacking configurations.

Metal locker with 30 drawers 54x34x140mm
Metal locker with 30 drawers 54x34x140mm

Workshop organization is very important, and what is better for storing components than well-organized containers? There are 30 transparent containers in this package and they are ideal for storing electronic components. On the front of each tray, there is a space where you can stick a label with the description of the component inside. Whole locker is made out of steel varnished in black.

 

Locker dimensions: 300x280x145mm
Container dimensions: 54 x 34 x 140 mm
Material: polypropylene and polystyrene containers, steel frame
• Number of drawers: 30
• We also have container dividers for this locker

20x transparent plastic container 100x56x125mm
20x transparent plastic container 100x56x125mm

Workshop organization is very important, and what is better for storing components than well-organized containers? There are 20 of these containers in a package and they are ideal for storing electronic components. They are quite large, so you can store larger products. We use identical ones like this in our warehouses! On the front of each tray, there is a space where you can stick a label with the description of the component inside. The containers can be taken apart and put back together, so they can be used in various stacking configurations.

 

Liquid flux, RF800, 100mL
Liquid flux, RF800, 100mL

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.

 

• Quantity: 100mL
• Density: 0,794g/cm3
• Soluble in water

 

REMARK: Be sure to close the flux after use.

Activated flux 40g
Activated flux 40g

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. In addition to all the above, this flux contains activators that further improve soldering, to the point that soldering is as simple and high quality as with solder paste.

 

• Weight: 40g

 

REMARK: Be sure to close the flux after use.

Protoboard 2x8cm
Protoboard 2x8cm

Well known protoboard 2 x 8 cm. Can be used for all of the ongoing mergers and soldering. Very good quality.

items per page