Tools & Lab equipment

The transparent cover is detachable and is held by four Phillips screws. Between the cover and the base, it is possible to place a rubber band that would waterproof the box (rubber band included). The transparent cover is convenient, because it allows you to see inside the box or can be used with light sensors/UV lights.

Waterproof box with non-transparent cover for projects. The cover is detachable on a snap mechanism it is not held by any screws. However the specs of the manufacturer we do not recommend this box to be used outside.

• Dimensions: 100 x 60 x 25 mm

Waterproof box with non-transparent cover for projects. The cover is detachable and is held by four Phillips screws. The box is waterproof and between the cover and the box, there can be placed a rubber band that would make the box safe from water.

• Dimensions: 115 x 90 x 55 mm

Waterproof box with transparent cover. The cover is detachable and is held by four Phillips screws. Between the cover and a box, it is possible to place a rubber band that would achieve the box to be waterproof, the rubber band comes within the box. A transparent cover is convenient because you can see inside or can be used with light sensors/UV rays.

• Dimensions: 158 x 90 x 60 mm

Waterproof box with non-transparent cover for projects. The cover is detachable and is held by four Phillips screws. The box is waterproof and in between the cover and the box you can place a rubber band to make the box even safer from water.

STLink standardly is known programmer for STM microcontrollers. Works with a whole specter of tools for STM, including mbed, Atollic Studio, Arduino IDE etc.

Soldermask is a layer on a printed circuit board that gives it a color, usually green, and is used to protect the tile from corrosion, easier soldering and visual appearance. This soldermask is in a liquid state, so you can easily apply it to places you want to protect further, such as wires that have been added or lines that have been damaged. It enters the solid state under UV light.

A vernier caliper is a tool that allows precise measurements of many physical dimensions. This one, made of high-strength stainless steel and with a digital display of the measured value.

ESD (ElectroStatic Discharge) or static electricity is a phenomenon where electricity flows suddenly between two electrically charged objects that are in touch or near each other. You experienced it, most likely,  when you touched something and felt “current” hurting you. Other than being unpleasant, there are no major consequences caused by ESD. But in electronics, ESD is very dangerous and can destroy your components and semiconductors.

This is where antistatic bracelet helps. If its other end is properly terminated to ground, it means that you are too. Through the 1M resistor, current flows to ground where it safely “goes” without being felt, and there won’t be any damage to components. It is always recommended to wear an anti-tatic bracelet whilte working with electronics.

Copper board used for making your own PCBs.

• Number of layers: 2
• Material: FR4
• Copper thickness: 35um
• Dimensions: 150 x 100 mm

Copper board used for making your own PCBs.

• Number of layers: 1
• Material: FR4
• Copper thickness: 35um
• Dimensions: 150 x 100 mm

Classic solder for working with a hand soldering iron. Solder paste is in the center of the solder, which simultaneously cleans the surface on which its soldering and gives a better grip of solder.

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.

A multimeter is a tool without no electrician can work, but when these little tools appear we ask ourselves what can we do without them! Give this components tester almost anything and it will tell you which component it is and even some more details about it! For example, you connect a resistor on it and it will show it is a resistor and give you his value in ohms. same goes for capacitors and inductors. Give it NPN or PNP transistor it will hFE and Vf. For diodes, it will tell you its voltage drop and capacity. The most interesting is that the tool will know which component is connected.

Classic and simple cutting pliers for cutting off excess material after soldering. Those can also be used for wire cutting or insulation removing.

High-quality spare probes for a multimeter.

If the soldering iron isn’t clean, neither will the the solder joint. This cleaning net allows quick tip cleaning by “stabbing” the soldering iron in it. When the net is filled with solder, simply remove it from the casing, clean the excess solder, return it back and use it again!

To pick up ultra-small components and put them in the right place you simply have to own a right tool. One such are the tweezers for SMD components which will enable you to handle 0603 components. With little more exercise even smaller ones, won’t be an issue. Of course, the tweezers are ESD safe so you shouldn’t worry that something will happen to your components.

The SMD components are very small and the tweezers help us to do the job properly. And what should we do when we are having larger components, such as integrated circuits that can be so large that we can not grab them with tweezers? SMD vacuum tweezer will help us here. It uses a vacuum to grab the surface of IC. The vacuum is activated by pressing a small button, so using this tool won’t be a problem. It comes with several tips for different integrated circuits.

M3 diameter standoff with a thread is ideal with bolts, nuts and screw + standoff combinations. It is most often used as a spacer on PCBs. A standoff is hexagon-shaped.

• Length: 25mm
• Threaded standoff
• Hexagonal (HEX) shape

M3 diameter standoff with a thread is ideal with bolts, nuts and screw + standoff combinations. It is most often used as a spacer on PCBs. A standoff is hexagon-shaped.

• Length: 20mm
• Threaded standoff
• Hexagonal (HEX) shape

M3 diameter standoff with a thread is ideal with bolts, nuts and screw + standoff combinations. It is most often used as a spacer on PCBs. A standoff is hexagon-shaped.

• Length: 15mm
• Threaded standoff
• Hexagonal (HEX) shape

M3 diameter threaded nut ideal for combinations with other M3 screws and nuts used as standoffs for PCBs. A standoff is hexagon-shaped.

• Length: 20mm
• A threaded standoff, screw matches M3 thread
• Hexagonal (HEX) shape