Soldering

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on both sides, as well as column and row markings.

As the name suggests, a spare handle for the soldering station from our offer.

Electrical tape is well known to everyone – it provides insulation between various connections. This is an extra-large, 30m roll. The color you receive will be randomly selected.

This PCB is also a protoboard. It offers both the simplicity and the functionality of a breadboard. It is the same size as the modular half-size breadboard and has the same connections to pins. The board allows you to make the temporary circuit from the breadboard permanent.

Product usage tips:

The board has three mounting holes for secure placement on different surfaces.

A 2-in-1 breadboard and PCB is what you get when combining the simplicity of the one and functionality of the other. It is the same size as the modular mini breadboard and has the same connections to pins. This PCB lets you move your circuit from a temporary connection on a classic breadboard to a more permanent place by soldering all the pieces.

Product usage tips:

The board can be secured in place by using the two mounting holes in the middle.

Classic solder for working with a hand soldering iron. In the center of the solder is a solder paste that simultaneously cleans the surface on which it is soldered and allows better adhesion of the solder. This solder is the so-called leaded.

• Quantity: 50g
• Diameter: 1.0mm
• Composition: Sn60Pb40

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

• Dimensions: 6cm x 4cm

Since the soldering iron is hot during operation, it is necessary to have a safe place to store it. This stand is affordable and serves its purpose. It also contains a sponge in its base on which it is possible to clean the tip of the soldering iron.

Kapton is a special type of material that is resistant to high temperatures and does not conduct electricity. When it is thinly rolled out and adhesive tape is placed on it, we get a kapton tape. In electronics, it is often used to protect plastic components from damage during soldering and as an insulator.

• Tape width: 30mm
• Tape length: 10m

The desoldering wick is a very practical aid during soldering. It is an interwoven copper wire soaked in flux to catch the solder. If you have a spot where you need to remove the solder, this tape will do a great job. Unlike the desoldering pump, this tape can completely remove the solder from the hole or from the pad.

• Length: 1.5m
• Width: 2.0mm

Soldering station with hot air is a combination that will solve all the problems regarding soldering and desoldering, whether it is THT or SMD components. The 50W soldering station has enough power to solder the components with the highest thermal mass, and comes with a pointed tip. Hot air will be useful for soldering and desoldering SMD components. It comes with three extensions with which it is possible to select the width of the hot air flow. With the station also comes a stand for both the soldering iron and for hot air.

• Maximum hot air power: 450W
• Hot air temperature range: 100℃ – 500℃
• Hot air flow: 120L/min max.
• Maximum power of soldering iron: 50W
• Hot air temperature range: 200℃ – 500℃
• Manufacturer and model: Gordak 968
• Input voltage: 230V

Soldering station SS-936A is a more serious part of equipment for electronic workshop. It contains a transformer in its base, thanks to which it can deliver high power at high speed. Therefore, you will easily solder the thickest wires and components to ground polygons. Power is up to 60W, adjustable temperatures up to 500 ℃ with a quality soldering iron that heats up quickly. It comes with spike tip, a soldering iron stand and a sponge for cleaning the tip of the soldering iron. If you are looking for a soldering iron that will serve you for a long time, without spending too much money, the SS-936A is an ideal choice!

The soldering iron is an essential tool for anyone who does something with electronics. Although we enjoy using more expensive soldering irons, this one is affordable and does the job – it will come in handy as a first or spare soldering iron, and with its price, it is affordable to everyone. The process of soldering permanently connects two pieces of metal. In electronics it is the joints between wires, components and boards. Whatever you want to do, you’ll always need to solder something, especially if you’re going to fix electronics – you must have a soldering iron. This soldering iron has a power of 40W, which is quite enough for soldering and desoldering in most cases.

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.

• Quantity: 15mL
• Density: 0,794g/cm3
• Soluble in water

REMARK: Be sure to close the flux after use.

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.

• Quantity: 100mL
• Density: 0,794g/cm3
• Soluble in water

REMARK: Be sure to close the flux after use.

Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. In addition to all the above, this flux contains activators that further improve soldering, to the point that soldering is as simple and high quality as with solder paste.

• Weight: 40g

REMARK: Be sure to close the flux after use.

Solder paste is used during SMT production, i.e. when SMT components are used. The paste is placed in specific places where it’s desired to achieve a solder joint, either by hand or with a stencil. After that, the components are placed and soldered in special ovens. This paste does not require cleaning after soldering (no clean). Paste is lead-free, which means it does not contain lead.

• Composition: Sn96,5Ag3Cu0,5
• Melting point: 252°C
• Solder ball sizes: 25-45µm
• Packaging: 1.4mL
• Lead-free
• No clean

At e-radionica.com solder paste is stored in the refrigerator, at a temperature of 8 ° C, which is the recommended storage temperature. We recommend that you choose express delivery for orders that contain this item in order to avoid product being exposed to high temperatures.

Solder paste is used during SMT production, i.e. when SMT components are used. The paste is placed in specific places where it’s desired to achieve a solder joint, either by hand or with a stencil. After that, the components are placed and soldered in special ovens. This paste does not require cleaning after soldering and has a low melting point.

• Composition: Sn62Pb36Ag2
• Melting point: 198°C
• Solder ball sizes: 25-45µm
• Packaging: 1.4mL
• Lead based
• No clean

At e-radionica.com solder paste is stored in the refrigerator, at a temperature of 8 ° C, which is the recommended storage temperature. We recommend that you choose express delivery for orders that contain this item in order to avoid product being exposed to high temperatures.

A set of heat shrinks that insulate the connections between the wires when heated.

The set consists of:

• • 60 heat shrinks 40 mm long, 2 mm in diameter
• • 30 heat shrinks 40 mm long, 3 mm in diameter
• • 16 heat shrinks 40 mm long, 4 mm in diameter
• • 16 heat shrinks 40 mm long, 5 mm in diameter
• • 16 heat shrinks 40 mm long, 6 mm in diameter
• • 10 heat shrinks 40 mm long, 9 mm in diameter
• • 8 heat shrinks 40 mm long, 10 mm in diameter
• • 8 heat shrinks 40 mm long, 11 mm in diameter

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

• Dimensions: 7cm x 9cm

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

• Dimensions: 15cm x 9cm

Where do we use flux? Flux is used by soldering. It is used to clean the pcb from any dust or oxidation (if there was any), which results with quality solder connections – solder attaches more easily to the pads where we want to put solder. Besides that, it improves electrical contact. Anyone who has tried it will know!

• Amount: 40g

Warning: Close the flux can after use.

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.

It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.