Shop

The USB Type-C is ubiquitous. We always wanted to add it to our electronics projects, and we’re sure you did too. Adding a USB Type-C connector to your projects is easier than ever thanks to this USB Type-C breakout board. It will allow you to send data to your device, as well as add power to the circuit.

The USB Type-C connector’s GND, CC2, SBU2, D-, D+, SBU1, CC1, and VUSB pins are broken out to the plated through-holes.

Product usage tips:

Male headers that are included need to be soldered to the board. The breakout board has two mounting holes and can be placed on any surface.

A breadboard is a piece of equipment that anyone who works with electronics must have. It enables connecting components and modules without soldering and in that way provides simpler testing, prototyping and learning. This breadboard is inside our Dasduino Beginner Kit.

Using this 8-bit shift register called 74HC595, you can increase the number of I/O(input/output) codes on your Dasduino/Arduino. Register itself uses 3 codes from the microcontroller, and in return it gives 8 I/O codes. The fact that you can connect a very large number of these registers and get a very large number of I/O codes by using only 3 codes from the microcontroller should not be neglected.

This transistor is also in our Dasduino Beginner Kit.

Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.

• Dimensions: 6cm x 4cm

Caps for THT potentiometer from our store that would make control much easier and would simply just look better.

Are you looking to start tinkering with electronics and Arduinos? Or perhaps you’re looking for a board to help you with electronic projects? Dasduino Core is the right choice for you. If you’re familiar with any of the retired Croduino products, you’ll feel right at home with this board. If not, no worries! Dasduino Core is made for makers of all skill levels! Not only will it execute the tasks in a breeze, but it will take up little space while doing so.

With just 63 mm wide and 22 mm high, Dasduino Core packs 22 I/O pins. It has 14 digital and 8 analog pins, which is plenty for almost all projects. It comes with a USB Type-C connection and is 100% compatible with the original Arduino boards and Arduino IDE. It comes with the Atmel Atmega328P microcontroller we all know and love. It works on 5V or battery voltage. There is also a 3.3V voltage regulator on the board for easy powering of 3.3V breakouts or easyC boards. Furthermore, it features Lithium-ion battery charger and connector, and a full color WS2812 RGB LED. An easyC connector will make connecting the Dasduino Core with other devices effortless.

Dasduino CORE (ATmega328) options:

The Dasduino CORE comes in 3 versions depending on the method of establishing a connection to the pins:

– without headers
– with male headers
– with female headers

0603 resistor 100k ohm with 5% tolerance.

25x Capacitor 1206 10uF.

Resistor 0603 1k ohm with precision of 5%.

Screw terminal for PCBs with a width of 3.5mm pin with two contacts.

The USB Type-A connection is still prevalent. If it’s in the electronic devices everywhere around us, it is only natural that we’d want it in our electronic projects. Adding a USB Type-A connection to your circuit is as easy as pie with this breakout board.

The breakout board breaks the GND, D+, D-, and VUSB pins out to the plated through-holes.

Dimensions: 22 mm x 22 mm
Connectors: USB Type-A (female)
Mounting holes: 2

If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Reaction game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The goal of the game is to press the button next to the LED as soon as it turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get?

It’s based on Attiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB.

The kit consists of:
• PCB
• Attiny404 microcontroller
• 4 LEDs
• 4 Pushbuttons
• A switch
• 4 resistors 330ohm
• CR2032 battery holder
• Battery CR2032
• Keychain holder

18650 battery holder allows easy use of lithium batteries in 18650 packaging. Otherwise, soldering these types of batteries is not recommended because the high temperature makes them lose their capacity. If you do not have a spot welding machine, we recommend that you get this kind of battery holder and you won’t have any problems with the loss of capacity, and it will allow you to use the batteries easily.

Did you ever want to turn on and off a device that needs large current or voltage? Whether operating on DC or AC, a relay is what you need. A relay is an electronic switch that is activated by a signal we send from a Dasduino or Arduino. This module further simplifies the whole process, because it contains everything you need for the relay to work, and you just have to connect it to the microcontroller and power supply. You don’t even have to think about voltages and currents, insulation between high and low voltage or grounding, everything is already taken care of on the board.

To pick up ultra-small components and put them in the right place you simply have to own a right tool. One such are the tweezers for SMD components which will enable you to handle 0603 components. With little more exercise even smaller ones, won’t be an issue. Of course, the tweezers are ESD safe so you shouldn’t worry that something will happen to your components.

Come on, everyone knows what the NE555 is! It is unlikely that we could make anything in our store without it, since it is inevitable in any kind of education, and is also able to solve the “time” problems in any type of assembly. It is a timer and can be used to create a pulse oscillator, delays …

5mm diffused LED diodes are great for experimenting and trying new things, which is why they are included in our Dasduino Beginner Kit (DBK)!

This 1200 mah battery is small, light and durable! Through a standard JST 2mm female connector it will give you normal 3.7V that will power your projects whole day (and night). It also has a built-in system for protection from too high a voltage (prevents overcharging), too low a voltage and short circuit. That’s how it protects the battery and ensure a long lasting and safe environment for your projects!

Warning: This battery must be charged with special charger principle CC/CV – like the charger recommended under. Li-ion batteries are dangerous! Read our tutorial (link right above) before use.

If you’re like us, you thought: “If only I could use a screen like this in my project”, first time you saw an e-book reader. Thanks to the exceptional sharpness and contrast, the ability to display in sunlight and truly unprecedented efficiency in terms of energy (it consumes energy only when changing the content on the screen), electronic paper is the ideal choice for many applications. Inkplate 6COLOR, continuing the tradition of the now well-known Inkplate series, continues to offer variations of e-paper accessible to hobbyists and everyone else in a way that we have made plug-and-play hardware, really easy to use and compatible with Arduino and micropython. Inkplate 6COLOR brings a unique innovation – the ability to display colors on the screen.

If we want to list only a few features, Epaper Inkplate 6COLOR has a 5.85-inch folded e-paper that displays a total of 7 different colors (Black, White, Red, Yellow, Blue, Green, and Orange). Considering the built-in dithering capability, the results you can get on the screen are really impressive. Powered by ESP32, you will have strong microcontroller with WiFi and Bluetooth on your disposal. It’s super-low-power (18uA) so you can use it for days, weeks, or months out of a single battery charge, and there is on-board Li-ion charger and RTC. Using our Arduino library (100% compatible with Adafruit GFX), it’s 5 minute work to get the board running for you. The Micropython module is available as well.  It’s 100% open-source for both software and hardware.

If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Stop me game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The LEDs go up and down, and your goal is to press the button as soon as the green LED turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get?

It’s based on Attiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB.

The kit consists of:
• PCB
• Attiny404 microcontroller
• 7 LEDs
• A pushbutton
• A switch
• 7 resistors 330ohm
• CR2032 battery holder
• Battery CR2032
• Keychain holder