Here you will find everything for soldering from our offer. Products like flux, various colored prototyping wires, soldering irons, prototyping boards, etc.
Showing 1–24 of 38 results
A set of heat shrinks that insulate the connections between the wires when heated.
The set consists of:
It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.
The soldering iron is an essential tool for anyone who does something with electronics. Although we enjoy using more expensive soldering irons, this one is affordable and does the job – it will come in handy as a first or spare soldering iron, and with its price, it is affordable to everyone. The process of soldering permanently connects two pieces of metal. In electronics it is the joints between wires, components and boards. Whatever you want to do, you’ll always need to solder something, especially if you’re going to fix electronics – you must have a soldering iron. This soldering iron has a power of 40W, which is quite enough for soldering and desoldering in most cases.
Classic solder for working with a hand soldering iron. Solder paste is in the center of the solder, which simultaneously cleans the surface on which its soldering and gives a better grip of solder.
If the soldering iron isn’t clean, neither will the the solder joint. This cleaning net allows quick tip cleaning by “stabbing” the soldering iron in it. When the net is filled with solder, simply remove it from the casing, clean the excess solder, return it back and use it again!
This PCB is also a protoboard. It offers both the simplicity and the functionality of a breadboard. It is the same size as the modular half-size breadboard and has the same connections to pins. The board allows you to make the temporary circuit from the breadboard permanent.
Product usage tips:
The board has three mounting holes for secure placement on different surfaces.
Desoldering wick is a very practical tool for every workshop. It’s a braided copper wire, soaked in flux, so it catches solder effectively. If you have a spot from which you need to remove the solder, this strip will do a great job. Unlike the discharge pump, this strip can completely remove the solder from a hole or a pad. 1.5m should last long since you spend only one or two centimeters per one desoldering.
• Lenght: 1.5m
• Width: 1.9mm
Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.
• Quantity: 100mL
• Density: 0,794g/cm3
• Soluble in water
REMARK: Be sure to close the flux after use.
Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. In addition to all the above, this flux contains activators that further improve soldering, to the point that soldering is as simple and high quality as with solder paste.
• Weight: 40g
REMARK: Be sure to close the flux after use.
Well known protoboard 2 x 8 cm. Can be used for all of the ongoing mergers and soldering. Very good quality.
It is extremely easy to remove insulation and solder with this stranded copper wire. It will serve great in small projects and prototypes.
Since the soldering iron is hot during operation, it is necessary to have a safe place to store it. This stand is affordable and serves its purpose. It also contains a sponge in its base on which it is possible to clean the tip of the soldering iron.
The desoldering wick is a very practical aid during soldering. It is an interwoven copper wire soaked in flux to catch the solder. If you have a spot where you need to remove the solder, this tape will do a great job. Unlike the desoldering pump, this tape can completely remove the solder from the hole or from the pad.
• Length: 1.5m
• Width: 2.0mm
Where do we use flux? Flux is used by soldering. It is used to clean the pcb from any dust or oxidation (if there was any), which results with quality solder connections – solder attaches more easily to the pads where we want to put solder. Besides that, it improves electrical contact. Anyone who has tried it will know!
• Amount: 40g
Warning: Close the flux can after use.
Classic solder for working with a hand soldering iron. In the center of the solder is a solder paste that simultaneously cleans the surface on which it is soldered and allows better adhesion of the solder. This solder is the so-called leaded.
• Quantity: 50g
• Diameter: 1.0mm
• Composition: Sn60Pb40
A 2-in-1 breadboard and PCB is what you get when combining the simplicity of the one and functionality of the other. It is the same size as the modular mini breadboard and has the same connections to pins. This PCB lets you move your circuit from a temporary connection on a classic breadboard to a more permanent place by soldering all the pieces.
Product usage tips:
The board can be secured in place by using the two mounting holes in the middle.
Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.
• Dimensions: 15cm x 9cm
Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on both sides, as well as column and row markings.
Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.
• Dimensions: 7cm x 9cm
Protoboard used for the permanent connection (also known as soldering) of electronic components. High quality, with solder mask on one side, as well as column and row markings.
• Dimensions: 6cm x 4cm
Kapton is a special type of material that is resistant to high temperatures and does not conduct electricity. When it is thinly rolled out and adhesive tape is placed on it, we get a kapton tape. In electronics, it is often used to protect plastic components from damage during soldering and as an insulator.
• Tape width: 30mm
• Tape length: 10m
Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This liquid solder is applied with a brush to the solder spots on the tile.
• Quantity: 15mL
• Density: 0,794g/cm3
• Soluble in water
REMARK: Be sure to close the flux after use.
Electrical tape is well known to everyone – it provides insulation between various connections. This is an extra-large, 30m roll. The color you receive will be randomly selected.
Flux is used during soldering to clean the board from dirt and possible oxidation (if any) which results in quality solder joints – solder is much easier to catch in the solder spot. In addition to cleaning, it also provides better wetting properties, which means that the solder will adhere better and more properly to the legs of components or solder joints. All this makes soldering much easier. This one comes in the form of a gel that is applied through a syringe, so setting it up is even easier.
• Quantity: 10mL
• Melting point: 150C