🚚 Free delivery on orders over: €35 Croatia • €60 EU • $100 US

Shop

24/7 free customer and technical support

Comprehensive documentation

Open-source hardware and software

2-year Warranty - no questions asked

Sort by:
Threaded insert M3 3mm
Threaded insert M3 3mm

The threaded insert is used to repair a damaged thread, for inserting into soft materials where it provides a permanent thread (eg. plastic).

Screw M3 6mm
Screw M3 6mm

Standard M3 countersunk head screw.

 

1N4007 diode
1N4007 diode

Ordinary and well-known rectifier diode 1N4007. It’s often used for rectification of voltage, protection from the wrong polarity, different projects with breadboard etc.

Max. voltage that this diode can endure is 1000V and max. current it can carry out is 30A.

 

RFID card
RFID card

RFID card is white and the size of standard credit card. We promise that it will fit into any standard wallet! Comes with random unique code.

 

RFID card comes in two variants, 125kHz or 13.56MHz.

RFID tag
RFID tag

Additional passive RFID tag for use with our RFID readers. It si practical as key ring.

 

RFID tag comes in two variants, 125kHz or 13.56MHz.

Coming soon Simon says game Solder Kit
Simon says game Solder Kit

If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this soldering kit is a great opportunity. Simon says game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The goal of the game is to press the buttons in the same order as LED turn on. With every correct answer, the game gets a bit harder. How many correct answers can you get?

 

It’s based on Attiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB.

 

The kit consists of:
• PCB
• Attiny404 microcontroller
• 4 LEDs
• 4 Pushbuttons
• A switch
• 4 resistors 330ohm
• CR2032 battery holder
• Battery CR2032
• Keychain holder

easyC cable
easyC cable

easyC system is for easy connection of microcontroller plates, sensors and actuators, which enables rapid prototyping without the possibility of error. The connection between the modules takes place with simple and pre-prepared cables, and easyC modules have connectors that fit the cables. easyC is based on I2C communication.

 

easyC-compatible cables with easyC connectors on both ends, available in different lengths.

Male header 40-pin
Male header 40-pin

Classical male header with 2.54mm pin spacing (0.1 ‘). 40-pin.

Crystal white 5mm LED diode
Crystal white 5mm LED diode

10 pieces pack of crystal white LEDs.

JST 2-pin male THT connector
JST 2-pin male THT connector

JST (more precisely JST XH) connectors are today the most common connectors for rechargeable lithium batteries but are also used for many other applications where a fast, easy and convenient connection is required.

Ceramic capacitor 100nF 50V
Ceramic capacitor 100nF 50V

Commonly used in a ceramic capacitor performance – Capacitor 100nF always come in handy 🙂

 

Generic NPN transistor TO-92
Generic NPN transistor TO-92

2N2222 is the most basic NPN transistor that you can find and it can be found in our Dasduino Beginner Kit. It can be used for amplifying Dasduino’s current, as a switch or anything else that you would like to do with the BJT transistor.

Pushbutton 12mm
Pushbutton 12mm

Large pushbutton will often be more practical than the small one (classic pushbutton). With dimensions of 12mm x 12mm it can be pushed in the breadboard, but it is also suitable for ordinary drill boards.

 

Pushbutton
Pushbutton

Pushbutton is a small button that fits with the breadboard. It has two states: connected(ON – when the button is being pressed) and disconnected(OFF – when the button is not being pressed). It can be used, for example, as a switch. This pushbutton comes in Croduino for beginners set.

5mm RGB LED diode - common cathode(-)
5mm RGB LED diode - common cathode(-)

5mm RGB LEDs in a classic through-hole version with 4 pins. Each one representing one color (+), while the longest pin being a common cathode (common negative) for all three colors.

 

Photoresistor (LDR)
Photoresistor (LDR)

A photoresistor is a type of resistor that changes its resistance depending on a light that falls on it. They are super simple for making something that is needed to keep track of the amount of the light(for example, it turns the light on when it is dark).

SPDT THT switch for breadboard
SPDT THT switch for breadboard

SPDT (single-pole, dual-throw) is simple switch which connects central contact with one of the other two contacts located inside its housing.

NFC sticker 13.56MHz
NFC sticker 13.56MHz

NFC sticker (Near Field Communication) is a wireless communication system that succeeds RFID. This sticker contains a small NFC tag operating at 13.56 MHz, with 1 kB EEPROM memory that supports up to 100,000 write cycles.

It is based on the MIFARE Classic 1K chip, a widely used and reliable standard for contactless data storage and access applications.

 

 

Servo motor TowerPro SG90
Servo motor TowerPro SG90

Sg90 servo is the type of motor that can turn the lever that is hitched to it very precisely and in that way control different things. This little servo motor is great for education and demonstration, but can also be used for real things that do not need great power for circumvolution (for example small vents).

Female header 8-pin 2.54mm
Female header 8-pin 2.54mm

Female header with 2.54mm (0.1 ”) classic pin spacing.

 

• Distance between pins: 2.54mm(0.1”)
• Number of pins: 8

easyC cable with female headers
easyC cable with female headers

This easyC cable exposes all the pins on the easyC connector. Using this cable, any easyC board can be connected to an experimental board or vice versa.

items per page

11 years in the industry

Customers in 80+ countries

20,000+ satisfied customers

250+ Soldered-designed products