Sensors

DS18B20 is a waterproof temperature sensor packed in metal and waterproof housing. For communication with Dasduino/Arduino, it uses only one wire and it is possible to put up to 127 sensors on one code and measure temperature in 127 different places by using just one wire!

Check out: „How to use a module?“  in the TUTORIAL section for the information on how to use the sensor, how to connect it to Dasduino/Arduino and downloading the library.

HC-SR04 is a widely used and popular sensor that can be used for measuring the distance between itself and the object that is placed in front of the sensor. Connecting to Dasduino itself is simple, the sensor requires only two codes for controlling and uses 5V voltage. There is also a library that provides us with distance information. Make sure you check „How to use module“ in the TUTORIALS category.

How many times have you watered your plants and feared you’re overdoing it? With the simple soil humidity sensor, those worries are a thing of the past! This two-part sensor is straightforward to use. The two exposed prongs go into the soil and send the humidity information to the sensor via the connected wire. The more water is in the ground, the better the results will be.

The two pieces are connected with the provided JST-SH 2-pin cable. The sensor uses the LM393 differential comparator. The main benefit of this board is ability to give analog and digital output. By setting the potentiometer on the board, you are able to get digital signal at the DO pin when signal crosses certain value, while analog values will be present on the AO pin at all times.

The INA219 is a digital device that allows the measurement of current, voltage, and therefore power. Simply, connect wire serial through this device and it will give all the information provided via I2C communication. It is very simple and reliable to use. It has a jumper for making changes to the I2C address so you can connect more than one INA219 to single microcontroller.

The maximum current of the measurement is determined by the shunt resistor found on the plate which is 0.1ohm (± 3.2A). Yes, it can measure the power in both directions! If you want to measure other currents or smaller currents more precisely, check out the datasheet to change that resistor. The maximum voltage that can be measured is 26V.

The APDS-9960 is a small sensor that measures four things at once. It recognizes the movements you make in front of it (up, down, left, right) and it can identify the proximity of the object, so you have two more movements: to the sensor and from the sensor. In addition, it has an ambient light sensor and a color sensor which gives red, green, and blue (RGB) colors as output. This sensor with many features was even built into the Samsung Galaxy S5 smartphone.

All gestures are detected at a distance of 10 to 20 cm and it has built-in UV and IR filters to make sure it won’t be confused by other sources of light. Connected using well-known I2C communication.

DHT11 is the simplest temperature and humidity sensor that can find. It connects to Dasduino in a very simple way using just one code (video below) and gives you back two variables as temperature and humidity.

It does not require extra calibration to work, just plug it in and use it. Look up the library for it in the TUTORIAL section.

Ensure a safe and healthy environment with our High-Precision Electrochemical Cl₂ Gas Sensor Breakout. This advanced sensor module is specifically designed to detect chlorine gas (Cl₂) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical H₂S Gas Sensor Breakout. This advanced sensor module is specifically designed to detect hydrogen sulfide (H₂S) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical NH₃ Gas Sensor Breakout. This advanced sensor module is specifically designed to detect ammonia (NH₃) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical O₃ Gas Sensor Breakout. This advanced sensor module is specifically designed to detect ozone (O₃) with exceptional accuracy, making it ideal for various applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical CO Gas Sensor Breakout. This advanced sensor module is specifically designed to detect carbon monoxide (CO) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to residential safety systems.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical NO Gas Sensor Breakout. This advanced sensor module is specifically designed to detect nitric oxide (NO) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical NO₂ Gas Sensor Breakout. This advanced sensor module detects nitrogen dioxide (NO₂) with exceptional accuracy, making it ideal for various applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Ensure a safe and healthy environment with our High-Precision Electrochemical SO₂ Gas Sensor Breakout. This advanced sensor module is specifically designed to detect sulfur dioxide (SO₂) with exceptional accuracy, making it ideal for a range of applications, from industrial monitoring to environmental studies.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

This breakout board is perfect for industrial safety, environmental monitoring, and research projects and provides a reliable foundation for precise gas detection solutions. Integrate this sensor into your systems to ensure timely alerts and maintain optimal safety standards.

Expand your gas detection capabilities with our versatile High Precision Electrochemical Gas Sensor Breakout, designed to work with a variety of electrochemical sensors. This breakout board provides the necessary interface and support for integrating different types of gas sensors, allowing you to customize your gas detection solutions to meet specific needs.

The breakout board works with both 3.3V and 5V power supplies. The EasyC connector provides a fast and easy connection with the microcontroller board. The board provides both analog and digital output with integrated ADC. The analog front end is fully programmable with I2C communication.

Compatible sensors:

• Sulfur Dioxide (SO₂) SGX-4SO2 : Detection Range: 0-20 ppm
• Nitric Oxide (NO) SGX-4NO-250: Detection Range: 0-250 ppm
• Nitrogen Dioxide (NO₂) SGX-4NO2: Detection Range: 0-30 ppm
• Carbon Monoxide (CO) SGX-4CO: Detection Range: 0-2000 ppm
• Ozone (O₃) SGX-4O3-20: Detection Range: 0-20 ppm
• Ammonia (NH₃) SGX-4NH3-300: Detection Range: 0-300 ppm
• Hydrogen Sulfide (H₂S) SGX-4H2S-100: Detection Range: 0-100 ppm
• Chlorine (Cl₂) SGX-4CL2: Detection Range: 0-10 ppm

On this module, there is a component, a phototransistor, which is capable of detecting infrared radiation. Since fire emits a large amount of infrared radiation, this sensor will detect it, but that is not its only application. Wherever there are IR (infrared) waves, this sensor will detect them, including from solar radiation.

The simple sensor has easyC connectors, which enables quick and easy connection with Dasduino microcontroller boards.

Discover the magic of motion tracking with our all-in-one Accelerometer, Gyroscope & Magnetometer LSM9DS1TR Breakout! This mini but mighty module bundles together a 3D accelerometer, a 3D gyroscope, and a 3D magnetometer. It lets you monitor not only linear and rotational movements but also the magnetic field surrounding your projects. Despite its pocket-size, it offers high-accuracy measurements — ±16 g for the accelerometer, ±2000 dps for the gyroscope, and ±16 Gauss for the magnetometer.

It has an embedded temperature sensor, FIFO buffer for data management, and interrupt features to signal your microcontroller when data is ready or when a certain event occurs. Plus, with I2C interface, it can easily connect with a variety of microcontrollers.

Our LSM9DS1TR breakout merges high-end capabilities with a user-friendly approach. It operates within a supply voltage range of 2.4V to 3.6V, making it compatible with both 3.3V and 5V systems. Its low-power and power-down modes optimize performance without draining too much energy.

This breakout board comes with 2 easyC connectors which will simplify connection with microcontrollers. By using the easyC module connection system, forget about incorrectly connected or, in the worst case, damaged modules.

Unleash the potential of digital control with our Rotary Encoder breakout board. Compact and powerful, this module makes working with rotary encoders easy. Rotary encoders are versatile input devices that convert angular position or button movement into digital signals. With the ability to detect direction and distance of rotation, they are perfect for controlling a variety of equipment such as volume knobs on audio devices, motors in robotics, or navigation controls in user interfaces.

Our breakout board simplifies the use of rotary encoders by utilizing easyC technology, making it easily connectable with microcontrollers or other circuits. It accepts input from a rotary encoder and translates it into signals that your microcontroller can interpret. In addition to the aforementioned rotary encoder module, the board also features a small ATTiny404 microcontroller, as well as a switch for selecting the I2C address. This breakout board comes with 2 easyC connectors for easy plug-and-play into the easyC system. If you don’t want to use easyC, the module can also be used via standard headers.

Step into the world of motion sensing with our nifty Accelerometer & Gyroscope LSM6DSO breakout! Small but mighty, this breakout board combines a 3D accelerometer and a 3D gyroscope on one tiny platform, letting you track both static and dynamic motions of your projects with ease. Its compact size doesn’t mean a compromise on performance – in fact, it offers high-resolution measurements of up to ±16 g and ±2000 dps respectively. So whether you’re building a drone, a VR game, or an IoT gadget, our LSM6DSO breakout will be your perfect companion for precise and efficient motion tracking.

Our LSM6DSO breakout is all about combining high-performance capabilities with user-friendly design. It operates on a supply voltage range of 1.71V to 3.6V, making it compatible with both 3.3V and 5V systems. Its power-saving features ensure that your projects keep running smoothly without draining too much energy. So, why wait? Add a dash of engineering magic to your projects with our Accelerometer & Gyroscope LSM6DSO breakout! With I2C interface, it’s a breeze to connect with various microcontrollers.

This breakout board comes with 2 easyC connectors which will simplify connection with microcontrollers. By using the easyC module connection system, forget about incorrectly connected or, in the worst case, damaged modules.

Embrace the fascinating world of motion tracking with our Accelerometer & Gyroscope LSM6DS3 Breakout! This handy little board integrates a 3D accelerometer and a 3D gyroscope, allowing you to monitor both linear acceleration and rotational motion in your projects. Despite its compact form, it packs a punch with high-resolution measurements of up to ±16 g and ±2000 dps respectively. Whether you’re building a gesture-controlled robot, a fitness tracker, or a drone, our LSM6DS3 breakout is here to ensure precision and reliability in every motion tracking task.

But it’s not just about tracking movement. Our LSM6DS3 breakout comes with an array of impressive features to add extra layers of sophistication to your projects. It features an embedded temperature sensor, providing crucial temperature data in environments where accurate motion tracking is a must. Additionally, it boasts a FIFO (First In, First Out) buffer that allows you to store and manage data efficiently, offering you greater control over your motion tracking applications. The board uses I2C interface, providing compatibility with a multitude of microcontrollers.

Our LSM6DS3 breakout is a seamless blend of high performance and user-centric design. Operating on a supply voltage range of 2.5V to 3.6V, it is compatible with both 3.3V and 5V systems. Its low-power operating modes ensure optimal performance without significant energy consumption. Start your journey towards motion mastery with our Accelerometer & Gyroscope LSM6DS3 Breakout and add that unique engineering touch to your projects!

This breakout board comes with 2 easyC connectors which will simplify connection with microcontrollers. By using the easyC module connection system, forget about incorrectly connected or, in the worst case, damaged modules.

The LSM6DSO32 sensor breakout is a compact and versatile sensor module designed to provide precise motion sensing capabilities for various applications. It is based on the LSM6DSO32, a high-performance 6-axis Inertial Measurement Unit (IMU) manufactured by STMicroelectronics.

The breakout board features a tiny yet powerful chip that combines a 3-axis accelerometer and a 3-axis gyroscope, allowing it to measure linear acceleration and angular rate in three dimensions. This makes it an ideal choice for projects that require motion tracking, orientation detection, gesture recognition, and activity monitoring.

One of the key advantages of the LSM6DSO32 sensor breakout is its low power consumption, making it suitable for battery-powered applications, such as wearables, IoT devices, and remote sensing systems. Additionally, the breakout board offers flexibility and ease of use with its I2C and SPI communication interfaces, allowing seamless integration with a wide range of microcontrollers and development platforms.

This breakout board comes with 2 easyC connectors which will simplify connection with microcontrollers. By using the easyC module connection system, forget about incorrectly connected or, in the worst case, damaged modules.

A PIR (passive infrared) motion sensor is a device that detects physical movement within its field of vision by sensing changes in infrared radiation. This sensor works on the principle of detecting thermal thermal signals emitted by objects, mostly warm-blooded creatures like humans. The “passive” in the name refers to the fact that the sensor itself does not emit or radiate any energy for detection.

When it detects motion, the sensor sends a digital signal to the microcontroller. The angle that the sensor “sees” is 100 degrees and reaches up to 5 meters. It is often used in a variety of applications, including home security systems, automatic lighting, and energy management, among others.

Our breakout board simplifies the use of the PIR sensor by using easyC technology, making it easily connectable with microcontrollers or other circuits. It accepts input from the PIR sensor and translates it into signals that your microcontroller can interpret. In addition to the aforementioned PIR sensor, the board also contains a small ATTiny404 microcontroller, as well as a switch for selecting the I2C address. This breakout board comes with 2 easyC connectors for easy integration into the easyC system. If you do not wish to use easyC, the module can also be used via standard headers.

How many times have you watered your plants and feared you overdid it? With the capacitive soil sensor, those worries are a thing of the past!

Most cheap soil sensors work on the resistance principle, where there are two prongs and the sensor measures the conductivity between them. They work fine at first, but eventually begin to oxidize due to the exposed metal. Even if they are gold plated! Due to oxidation, the resistance goes up and up, so you have to constantly recalibrate your code. Also, resistance measurements do not always work in loose soil.

This design with capacitive measurement is superior. Capacitive measurements use only one prong, have no exposed metal, and do not introduce direct current into your plants.