Shop

Water is essential for life on Earth. Using water efficiently is very important. With the easy-to-use simple rain sensor, farmers can save water while irrigating their crops. The sensor will alert them to shut down the water supply when it senses rain. It can even act as an automatic on and off switch, like turning on wipers on a car when it senses rain.

This sensor has two pieces – the rain sensor and the simple sensor. The rain sensor has nickel-coated lines on both sides. It measures moisture and outputs the data to the simple sensor that reads it. The simple sensor uses the LM393 differential comparator. The main benefit of this board is ability to give analog and digital output. By setting the potentiometer on the board, you are able to get digital signal at the DO pin when signal crosses certain value, while analog values will be present on the AO pin at all times.

WS2812B is an extremely interesting LED that can emit light in red, green or blue – or any combination of these three colors, able to show a total of approximately 16 million different colors. On this board diodes are arranged in a circle. They are controlled by a single pin with only few lines of code from Arduino IDE. That’s possible thanks to the integrated controller inside the LED itself!

This module allows you to connect a Dasduino, or similar microcontroller, to a RS-485 communication protocol. The RS-485 is used to send data over long distances (up to 1200m) at 20Mbps and in high-noise environments, such as industrial. The module works on 5V and requires between 120μA and 500μA of current.

• Voltage: 5V
• Based on: SN65176BDR
• Dimensions: 38 x 2mm

The RS-232 is a standard and very popular protocol for communication between two devices. It is a full-duplex protocol which means it can receive and send data at the same time, and data is sent at voltages from + 3V to + 15V for a digital “one” and from -3V to -15V for digital “zero”. This provides a more secure environment for data transmission which is resistant to noise or interference, which is why the RS-232 is often used in industry. This module converts serial communication to RS232.

• Communication lines: TX, RX
• IC:232 MAX

• Voltage: 3.3V – 5.5V
• Dimensions: 22 x 22 mm

Unlock precise power monitoring for your electronics projects with the INA219 Voltage & Current Sensor Breakout. This device accurately measures current, voltage, and power, providing data via a simple I2C interface. Designed for seamless integration, it’s perfect for Arduino, Raspberry Pi, and other microcontroller-based systems, allowing you to track energy consumption, monitor battery life, or implement power management solutions with ease.

Featuring a 0.1-ohm shunt resistor, the INA219 breakout can measure currents up to ±3.2A and voltages up to 26V, offering bidirectional measurement capabilities. Its design includes a jumper for I2C address modification, enabling multiple sensors on a single microcontroller bus. Whether you’re a hobbyist or a professional, the INA219 provides reliable and accurate data, making it a tool for any project requiring detailed electrical parameter insights.

Beyond its technical capabilities, the INA219 breakout emphasizes user-friendliness and open-source principles. With documentation and complimentary technical support, you’ll have all the resources needed to get started quickly. Its easyC compatibility further simplifies connections, allowing for rapid prototyping without complex wiring.

Fuel gauge is a special type of accessory for lithium batteries that very precisely measures the state of the battery. This includes current voltage [mV], state of charge [%] and probably most interestingly: remaining capacity in the battery [mAh]. It is used with 1S batteries, and provides all this information via the I2C interface.

On our board you can find easyC connectors which allow I2C communication with microcontroller. Also, there is a JST input for any pouch battery you can find in our offer, as well as quick connect terminal connector for input if your source doesn’t have JST connector.

For very precise measurements of the amount of light, take this digital light sensor into account (ALS – Ambient Light Sensor). In addition, the LTR-507ALS also measures the proximity (PS – Proximity Sensor) of the object to the sensor. It sends all this data via I2C communication, which is easy to read via our Arduino library.

Micro:bit is a very interesting board with lots of options that are used by many children in school or hobbyists, but who can say no to new features! So we decided to make a micro:bit add-on that will enable internet connection via WiFi! Finally, you’ll be able to connect your micro:bit projects to the Internet and to connect to the well known Internet of Things. WiFi:bit add-on is easy to use through a MakeBlock add-on or using completed Python examples.

Just insert micro:bit to the add-on, plug in the power cable (required) and you are ready! Open the examples and start sending and receiving data from the internet. There are even two easyC connectors on the WiFi add-on, which allow the simplest connection of I2C sensors and actuators with micro:bit. There are also available pins on the board which are isolated on standard spacing used for breadboard connections or connections with cables to additional components!

Ever wanted to build your own weather station using Arduino? Then the BMP180 breakout board with precision sensor from Bosch might interest you. The digital sensor on the board precisely measures the changes in barometric pressure and temperature. It uses the piezoresistive effect to gather the information. Since the pressure varies depending on height, the sensor can measure altitude too. Very low current consumption and voltage allow this type of sensor to be used in many modern devices.

The design is 5V ready with an onboard regulator for 3.3V. The breakout board’s standard current consumption is very low, only 5 µA. It uses an I2C interface, and the I2C address is 0x77. No soldering, nor need for distinguishing between SDA and SCL is required due to easyC. The sensor has integrated EEPROM memory with data for calibration. The pressure is measured in steps of 1hPa (=0.01hPa =0,01mbar), and 0.1°C for temperature.

Product usage tips:

If there is an error while using the breakout board, see if it’s connected properly. Take a look at the pinout. If everything is properly connected, check if the I2C address of the breakout board is correct prior to programming it. The I2C 7-bit address should be 0x77. If everything is correctly connected and the I2C address is right, look through your code once again. There might be some bugs in the code that are stopping the sensor from working as it should.

BMP180 breakout board works very well in combination with any Dasduino board and OLED I2C 0.96” display breakout board. All of them use easyC so they can be connected in a matter of seconds. The BMP180 sensor can measure the barometric pressure and temperature, while the OLED display can show them. The breakout board also comes with two mounting holes so you can attach it onto something and it won’t budge.

To keep the sensor working for a long while, we would advise you not to use it in extreme conditions. Going over or below the temperature range will surely damage the sensor. Same with the pressure. Keep track of the current going through it. Allowing too high of a current through the breakout board will burn the sensor and render it completely useless.

Connecting the NRF24L01 can be tricky – you have to pay attention to the layout of the pins, adjust them to match those from the library and add a capacitor. This board solves all that, and it already comes with soldered headers, so just plug this board into your Dasduino and that’s it!

• Comes with NRF24L01+ module
• Dimensions: 38 x 22 mm

To connect to our PMS7003 air quality sensor easily, we designed this adapter. It allows you to connect the PMS7003 sensor to breadboard or to connect with cables.

WS2812B is an extremely interesting LED that can emit light in red, green or blue – or any combination of these three colors, able to show a total of approximately 16 million different colors. On this board, diodes are arranged in a line of 10. You can even connect these sticks in a line. They are controlled by a single pin with only a few lines of code from Arduino IDE. That’s possible thanks to the integrated controller inside the LED itself!

• Number of LEDs: 10
• Voltage: 5V
• LED type: WS2812B
• Current: max 60mA per LED
• Dimensions: 80 x 10 mm

WS2812B is an extremely interesting LED that can emit light in red, green or blue – or any combination of these three colors, able to show a total of approximately 16 million different colors. On this board, diodes are arranged in a circle. They are controlled by a single pin with only a few lines of code from Arduino IDE. That’s possible thanks to the integrated controller inside the LED itself!

These small LEDs are not just ordinary lights – each is unique because it has a built-in small integrated circuit (IC) that is able to turn on the LED light in 16 million different colors. IC is WS2812 and it uses a single wire that can control thousands of these LEDs. With a little imagination by putting these pixels, you get superior effects with a minimum effort. These lamps are easy to control with Dasduino.

Looking to add visuals to your Arduino projects? The I2C OLED breakout board is perfect for that. Because of its high contrast, you will be in awe of its crispness! The display is made from hundreds of LEDs, each representing one pixel in a 128×64 grid. Thus, it doesn’t need any backlight, and it needs less power than the classic LCD screens. That’s 8192 pixels all individually lit at your fingertips!

The design is 5V ready with an onboard regulator, so is compatible with any 3.3V board. The breakout board uses only about 20 mA, depending on active pixels. It is easy to control over the I2C interface. It is even easier to connect with the easyC system – no soldering required!

Display OLED I2C 0.96″ SSD1306 options:

The color of the OLED screen on the product can be:

– White
– Blue

This device uses MCP47A1 which is a single channel, 6-bit digital to analog converter with I2C compatible serial interface. There’s no integrated EEPROM memory which would allow DAC register and configuration bit values to be saved at powered off.

RTC (Real Time Clock) is a device that carefully and precisely tracks time and dates. It is extremely precise, so it is more suitable for long-term time tracking than clocks on microcontrollers. This breakout can work with an extremely low current and thanks to the alarm feature and interrupt pin, it will allow a microcontroller to enter sleep mode until its awaken by this RTC.

It has a built-in battery holder (battery not included) and even if power is lost, real-time tracking won’t be affected.

A module which enables the use of micro SD cards with Arduino via SPI communication. You can save various types of data on the SD card, create logs, read the information from it or perform various actions.

A battery protector is, simply put, a device that makes sure that something bad doesn’t happen to the battery. This small circuit board protects your lithium battery (of any capacity) from overcharge, overdischarge, overcurrent and short circuit. It has a JST connector for connecting the battery, and the battery can be directly soldered.

• Protects from: undervoltage, overvoltage, overcurrent, short-circuit current

• Protection IC: DW01

• Battery configuration: 1S1P (1-serial, 1-parallel)
• Battery type: Li-ion, Li-poly
• Dimensions: 22 x 22mm

The Color and Gesture Sensor APDS-9960 breakout is a compact and powerful module designed for multiple sensing capabilities. It enables gesture recognition, allowing it to detect movements such as up, down, left, and right. In addition to gestures, it features proximity sensing, accurately measuring the distance of objects within a range of 10 to 20 cm. This makes it ideal for interactive applications and touchless control systems.

Beyond gestures and proximity, the APDS-9960 includes an ambient light sensor that automatically adjusts brightness based on surrounding conditions. It also functions as an RGB color sensor, capable of detecting red, green, and blue light with precision. This makes it useful for applications where color-based decisions are required.

To ensure accuracy and minimize interference from external sources, the sensor is equipped with built-in UV and IR filters. It communicates using the widely adopted I²C interface, making it easy to integrate into microcontroller-based projects, robotics, and automation systems. Its reliability is further demonstrated by its use in commercial devices such as the Samsung Galaxy S5 smartphone.

This module is an excellent choice for open-source electronics enthusiasts, developers, and engineers looking to create interactive projects with gesture control, proximity detection, and color recognition. Whether you’re building an automation system, a touchless interface, or an intelligent lighting system, the APDS-9960 Color and Gesture Sensor provides a versatile and efficient solution.

A digital potentiometer is a device identical to a potentiometer, except that instead of a physical rotating part that adjusts the resistance, it uses digital communication. Namely, the resistance of the digital potentiometer is adjusted via I2C communication.

Our module is based on the MCP4018 IC which has a total of 128 steps between 0 and 5k resistance values. This would mean that it is capable of doing resistance steps of approximately 39ohms. It is controlled via I2C which makes it extremely easy to use.

The BQ24295 is a versatile Li-ion battery charger designed to provide efficient and reliable charging for single-cell lithium-ion or lithium-polymer batteries. It supports various charging modes, including constant current (CC) and constant voltage (CV) charging, to ensure the battery is charged quickly and safely.

The BQ24295 charger operates on a wide input voltage range, typically from 4.35V to 17V, allowing it to be powered by a variety of power sources, including USB ports and AC adapters. It also features integrated power path management, which allows simultaneous charging of the battery while powering the connected device, providing uninterrupted operation.

We made the easyC system for faster prototyping and easy connection between the components. However, some of the components have only one easyC port or you just want your cable managmenet made better. What to do in those cases? The easyC hub comes to the rescue! It has six connectors so you can easily expand your circuit. It’s as simple of a device as it can get.

Product usage tips:

You can connect easyC devices to the hub like you would to any other easyC device. Just plug the preferred easyC cable into the hub and a device you’re working with. That’s all there is to it.

You should avoid working with the hub in wet environments to ensure it lasts a long time. Be sure to watch the operating voltage of your circuit. Since the hub works on 3.3V, higher voltages can burn it and render it useless. There is a hole in the middle of the board so it can be secured to any surface.

Ever needed to connect two peripherals with the same I2C address to the same microcontroller? This module allows you to seamlessly connect up to eight I2C devices with identical addresses.. Using the TCA9548A IC, our breakout board provides flexibility, enabling control of up to 64 devices on the same I2C bus. This means you can integrate numerous sensors, such as 64 BME680s (because why not?), all managed by just one microcontroller, simplifying complex setups and expanding your possibilities.

Beyond its core capabilities, the TCA9548A breakout is engineered for compatibility and ease of use, especially within the Qwiic ecosystem. This adapter is convenient for makers and engineers looking for rapid prototyping solutions without the intricate wiring. Its broad voltage compatibility (1.65V – 5.5V) ensures integration with a wide range of microcontrollers, including Arduino and NULA boards, making it an addition to any electronics workbench. With its compact dimensions and clear pinout, integrating this multiplexer into your existing or new projects is easy and efficient.

This I2C multiplexer is designed and manufactured in the EU, guaranteeing great performance and durability. We offer documentation, quick start guides and dedicated technical support to ensure your success, including our open-source community. Choose our TCA9548A breakout for a high-performance solution that empowers your innovative projects with I2C communication capabilities.