Shop

Gas sensor MQ7 detects the presence of Carbon Monoxide (CO) in the air. The best results are given when alcohol is in liquid form, however, it still does an amazing job when measuring in gas form. It needs a bit of time to warm up in order to work correctly.

MQ-4 methane gas sensor registers the presence and concentration of natural gas and methane (CH4). The best results are given when gas is in liquid form, however, since situations like this are rare, it does its job pretty well when in gas form, too. It needs a bit of time to warm up in order to work correctly.

A 7-segment display is classical, often used and already familiar component. Size of a digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

7-segment display is classical with common cathode, often used and already familiar component. Size of the digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

A 7-segment display is a classic, often used and already familiar component. The size of the digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

If you use some laboratory equipment such as power source, signal generators or, in most cases, multimeters – you’ll find this cable very practical. It has 2 banana connectors – on one end so you could connect it to mentioned devices and on another end to connect it to alligator connector which allows you to connect to almost anything!

Connecting to other devices and controllers from improvised power sources becomes truly simple with this terminal. Just use a screwdriver to tighten your wires to the terminal and you’re ready!

Connecting to many other devices and controllers from improvised power sources becomes truly simple with this terminal. Just use a screwdriver to tighten your wires to the terminal and you’re ready!

LM 7805 is often used 5V linear regulator, this one is in the THT version.

Smaller booster (step-up) module. It increases input voltage to the desired level.

A through-hole holder for CR2032 3V battery which you can find on watches,  RTCs, toys, motherboard and other electronics.

BR2032 batteries are also suitable for this holder, but we do have one more battery type for you – CR2032 battery.

SMD Battery Holder for CR1220 3V battery, just like the one on our Croduino Damba.

USB mini-b female connector for a printed circuit board (PCB). It’s identical to the one used on Croduino Basic.

Dasduino Beginner Kit is a complete system for learning how to code and getting familiar with the main principles of electronics. With this set, you’ll be able to code the world and different electronic gadgets around you. Moreover, you’ll learn how to code your Dasduino (Arduino compatible board) in C programming language, connect electronic components and other things of importance in the electronics world. The best thing about this kit is that no experience in coding or electronics is required to get started.

This kit is an amazing choice for not only beginners, but schools, businesses, hobbyists and even colleges because it offers everything that is necessary for a individual to learn about electronics through their own project, while being at an affordable price.

Hobby version of Dasduino Beginner Kit has much more components than the basic version of the kit. It contains additional components and other actuators and sensors.

This kit consists of:

• Dasduino CORE + USB cable
• Set of cables for breadboard
• Breadboard
• 15x 10K resistor
• 25x 330ohm resistor
• 2x 5mm RGB LED diode
• 6x 5mm blue LED diode
• 6x 5mm red LED diode
• 6x 5mm yellow LED diode
• 6x 5mm green LED diode
• DHT
• 3x Photoresistor
• 6x Pushbutton
• Buzzer
• 3x MOSFET transistor IRF540
• 3x 2N2222 transistor
• Shift register 74HC595
• 6x Potentiometer 10k
• 3x Big pushbutton
• Relay, 1-channel
• LCD display 16×2
• 3x 1N4148 diode
• Ultrasonic distance sensor
• Motion sensor HC-SR501

If you usually do big projects or put on workshops, you know that there’s never enough of some components. Therefore, we’ve put together this set of wires, resistors and other primary components to make your everyday work or education much easier.

This set consists of:

• Breadboard
• Set of cables for breadboard
• 50x 330ohm resistor
• 45x 10k resistor
• 10x 2n2222 transistor
• 10x 1n4148 diode
• 5x photoresistor
• 10x pushbutton
• 5x potentiometer 10k
• 2x 100nF ceramic capacitor
• 5mm RGB LED diode
• 3x 5mm blue LED diode
• 3x 5mm red LED diode
• 3x 5mm yellow LED diode
• 3x 5mm green LED diode

H bridge supports an exchange of polarities on its outputs and therefore enables control of motor spins in both directions in a very simple way. It can also direct other devices that for certain usage require the exchange of polarities on their inputs.

Well known and popular 8-bit Atmel microcontroller which is used on the majority of modern Arduino boards as well as on Dasduino. This one is the SMD version, just as the one on Dasduino, which is used for soldering on PCBs and for usage in projects.

5mm diffused LED diodes are great for experimenting and trying new things, which is why they are included in our Dasduino Beginner Kit (DBK)!

MOSFET transistor N-channel has ideal characteristics that allow it to connect to Croduino/Arduino. With this transistor, you’re able to control devices that need big amounts of current or voltage – all of that via a microcontroller.

Large pushbutton will often be more practical than the small one (classic pushbutton). With dimensions of 12mm x 12mm it can be pushed in the breadboard, but it is also suitable for ordinary drill boards.

Mini breadboard for beginners or for fast prototyping.

The colors on offer are green, blue, red, white and black. We send them out randomly so you could get any of them. If you prefer a specific one, leave a message with your order letting us know which one and we’ll try to fulfill your wish. 🙂

Relay is a device with enables switching greater loads – ones that require more voltage/current. These relays can be found in our relays breakouts. It has NO and NC pins.

• Current needed for activation (current of Dasduino): 20mA
• Coil voltage: 5V
• Max. DC: 30V, 10A
• Max. AC: 250V, 10A

Crystal (oscillator) with a frequency of 16MHz.