Sale

Have you ever wondered how much natural gas and methane are present in your living room? You can easily measure it! The MQ4 breakout board is a user-friendly sensor that detects natural gas and methane (CH4) in the air. Once it reaches operating temperature, it quickly detects changes in air concentration within the range of 200 to 10,000 ppm.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

Product usage tips:

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

MQ sensors, including the MQ2 sensor, have the capability to detect various gases. The MQ2 sensor is specifically designed to detect combustible gases such as LPG (liquefied petroleum gas), butane, propane, methane, alcohol, hydrogen, and smoke. These gases are commonly found in residential, industrial, and automotive environments. The sensor’s sensitivity and responsiveness enable it to detect even trace amounts of these gases, making it a valuable tool for gas leakage detection, fire detection, and air quality monitoring. It takes a short time to heat up in order to work correctly.

The breakout board provides digital and analog information through the easyC system. Sensor readings are obtained through easyC.

Product usage tips:

When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Four mounting holes enable easy mounting to surfaces. The board comes with three male headers.

We are surrounded by invisible gases everywhere. While we generally don’t have to worry about them, under the right circumstances, they can be very combustible and dangerous. The MQ9 breakout board detects carbon monoxide, methane, propane, and other flammable gases so the right measures can be taken in time. The sensor detects carbon monoxide at 10-1000 ppm and other combustible gasses at 100-10000 ppm.

The digital and analog outs can be found on the through-holes. They are marked as DO and AO respectively. The digital output can be obtained by setting a threshold value with a potentiometer. The analog output will depend on the intensity of the gases.

Product usage tips:

The sensor needs 48 hours to preheat to optimal working temperature. If it detects some gas, the LED will glow. If there are no gases, it will remain off. The board can be attached to the project thanks to the two mounting holes. It comes with four pins that need to be soldered.

Due to its long life, the breakout board can be used for quite some time without a second thought. To prevent damage to the sensor, avoid dipping it in water or freezing it. Highly corrosive gases will weaken the sensor significantly.

Humans can detect many scents, but can have difficulties when it comes to differentiating gases. That’s why we use sensors like MQ6. It detects LPG and butane in the air. When heated to the optimum working temperature, it detects changes in air concentrations very quickly between 200 and 10000 ppm.

The DO pin stands for digital out. AO stands for analog out. The digital output is obtained by setting a threshold value using the potentiometer. The analog output will depend on the intensity of the gas around the sensor.

Product usage tips:

Preheating the sensor to the optimal working temperature takes 24 hours. The LED on the board will glow when gas is detected. It will remain off when it’s not. The board has two mounting holes for easy attachment to the project. It comes with four pins that need to be soldered.

You can use the board for years due to its long life. To prevent damage to the sensor, it should not be dipped in water or frozen. Highly corrosive gases will render the sensor useless. Cooking fumes and cigarette smoke will interfere with the sensor.

Is your office near a high-traffic area? Are you concerned about the amount of natural and liquefied petroleum gases in your work environment? The MQ5 is a simple-to-use sensor to put your mind at ease. It detects gas particles very quickly between 200 and 10000 ppm.

The breakout board works with both digital (DO) and analog signals (AO). The digital output is obtained by setting a threshold value with a potentiometer. The analog output will differ depending on the intensity of the gas.

Product usage tips:

The sensor takes 24 hours to preheat to optimal working temperature. When gas is detected, the LED will start glowing. It will remain off if it doesn’t detect anything. Two mounting holes enable easy mounting to surfaces. The board comes with four pins that need to be soldered.

The breakout board boasts a long life so you don’t have to worry about it suddenly breaking. Submerging the sensor underwater and freezing it will damage it beyond repair. Highly corrosive gases will also damage the sensor.

Have you ever wondered how much natural gas and methane are in your living room? You can easily measure that! The MQ4 breakout board is a simple-to-use sensor that detects the natural gas and methane (CH4) in the air. Once heated to working temperature, it detects changes in air concentrations very quickly between 200 and 10000 ppm.

On the through-holes, the DO stands for digital out and AO for analog out. The digital output is obtained by setting a threshold value using the potentiometer. The analog output will depend on the intensity of the gas around the sensor.

Product usage tips:

The sensor will take 24 hours to preheat to working temperature. The LED on the board will glow when gas is detected, and remain off when it’s not. The board can easily be secured in place using the two mounting holes. It comes with four pins that need to be soldered.

Due to its long life, you can use this board for years without much of a thought. Dipping the sensor in water and freezing it will damage it, so avoid doing that. Highly corrosive gases will weaken it significantly, making it useless.

The hall effect sensor (Hall Effect sensor) will be able to detect the magnetic field in its vicinity thanks to the aforementioned physical law. A magnetic field that can be created by a magnet, a current flowing through a conductor or some third source, the Hall effect sensor will recognize each.

This sensor has a programmed threshold at which it will change the state of its output signal, so it is a sensor with a digital output. Through the easyC connectors, it enables a simple connection with the microcontroller.

This sensor has two pieces – the rain sensor and the simple sensor. The rain sensor has nickel-coated lines on both sides. It measures moisture and outputs the data to the simple sensor that reads it. The simple sensor comes with easyC connectors onboard, which enables quick and easy connection with Dasduino microcontroller boards.

With the easy-to-use simple rain sensor, farmers can save water in irrigation. The sensor will alert them to shut down the water supply when it senses rain. It can even act as an automatic on and off switch, like turning on wipers on a car when it senses rain.

This module is a phototransistor that is capable of detecting infrared radiation. Since fire radiates a large number of infrared rays, this sensor will detect them, but this is not its only application. Wherever there are infrared waves, the sensor will detect them (including those from the sun). Using the built-in comparator on its outputs gives either digital (HIGH / LOW) or analog (0V-5V) signals, depending on the intensity of the IR radiation.

Light is one of the most important things in the life of most living beings. This is why it is common to work with light sensors when learning about electronics. A simple light sensor has a light dependent resistor (LDR) and sensor on a breakout board for easy wiring. The simple sensor comes with easyC connectors onboard, which enables quick and easy connection with Dasduino microcontroller boards.

As the name suggests, an LDR will change its resistance depending on the amount of light it is exposed to. The amount of light and resistance are inversely proportional. The more light it is exposed to, the less resistance it will have. So if there is more light, the board will have a resistance of several hundred Ohms. If the resistor is in the dark, it will have a resistance of several thousand Ohms.

For very precise measurements of the amount of light, take this digital light sensor into account (ALS – Ambient Light Sensor). In addition, the LTR-507ALS also measures the proximity (PS – Proximity Sensor) of the object to the sensor. It sends all this data via I2C communication, which is easy to read via our Arduino library.

Micro:bit is a very interesting board with lots of options that are used by many children in school or hobbyists, but who can say no to new features! So we decided to make a micro:bit add-on that will enable internet connection via WiFi! Finally, you’ll be able to connect your micro:bit projects to the Internet and to connect to the well known Internet of Things. WiFi:bit add-on is easy to use through a MakeBlock add-on or using completed Python examples.

Just insert micro:bit to the add-on, plug in the power cable (required) and you are ready! Open the examples and start sending and receiving data from the internet. There are even two easyC connectors on the WiFi add-on, which allow the simplest connection of I2C sensors and actuators with micro:bit. There are also available pins on the board which are isolated on standard spacing used for breadboard connections or connections with cables to additional components!

To connect to our PMS7003 air quality sensor easily, we designed this adapter. It allows you to connect the PMS7003 sensor to breadboard or to connect with cables.

This device uses MCP47A1 which is a single channel, 6-bit digital to analog converter with I2C compatible serial interface. There’s no integrated EEPROM memory which would allow DAC register and configuration bit values to be saved at powered off.

How many times have you watered your plants and feared you overdid it? With a simple soil moisture sensor, these worries are a thing of the past! This two-part sensor is easy to use. Two exposed prongs go into the soil and send moisture information to the sensor via a connected wire. The more water there is in the ground, the better the results will be.

The two parts are connected with the included JST-SH 2-pin cable. The simple sensor has easyC connectors on it, which enables quick and easy connection with Dasduino microcontroller boards.

The Hall effect sensor breakout with analog output is a versatile and reliable sensor module designed to detect and measure magnetic fields. It utilizes the Hall effect principle, where the presence of a magnetic field induces a voltage proportional to the strength and direction of the field.

This sensor module features an analog output, which provides a continuous voltage signal that varies in response to changes in the magnetic field. The analog output allows for precise and real-time monitoring of magnetic field strength. It is commonly used in applications such as position sensing, current sensing, and speed detection.

The module is typically powered with a supply voltage ranging from 2.25V to 5V, making it compatible with a wide range of systems.

Classic power adapter which converts other power connectors to EU schuko power connector

Compressed air is most commonly used for cleaning electronics. Since the gas from the container comes out under high pressure, it is perfect for cleaning dust and all particles. It is colorless, odorless and leaves no traces. It is able to reach even the most inaccessible parts of any electronic equipment and is especially practical for cleaning places you don’t want to touch.

• Package: 300mL

This lubricant contains molybdenum disulfide which has a very low frictional resistance. It is used for metal parts and prevents them from collapsing and wearing out. It is very often used to lubricate parts of heavy industrial equipment, such as forklifts or cranes. For application at temperatures up to 150C.

• Temperature : -30 – 150C
• Package: 100mL

Copper-based lubricant is intended for lubrication of all types of mechanical joints that work at extremely high temperatures which makes it suitable for use in owen.

• Package: 100mL
• Temperature range: -40 – 1100°C

Kontakt S is used to remove oxides and sulfides from electrical contacts and it protects against corrosion. This ensures a smooth flow of current through the connector, even in cases of already oxidized and worn contacts. It is especially useful in audio products, where the cleanliness of the contact is crucial.

• Package: 400mL
• Spray
• Density: 0,74g/cm3

This RF converter is used to connect coaxial cables. The converter has a male input on one side and a male output on the other.

This connector allows the connection of an antenna with a male SMA connector to a board at a 90-degree angle.

Classic current adapter from switching the american to european type connector.

• Dimensions: 25.5 x 30 x 14mm