In this category there are various electronic components that we offer. Resistors, capacitors, transistors, connectors, etc.
Showing 25–48 of 248 results
LM 7805 is often used 5V linear regulator, this one is in the THT version.
7805 is often used 5V linear regulator, in this version of Through Hole (THT). It can only provide 100mA current at 5A it carefully used. Be sure to add the output decoupling capacitors.
78m05, often used 5V linear regulator in DPAK SMD package.
Generic (generally used) 5V linear regulator in Through Hole (THT) version. Be sure to add decoupling capacitors to the output.
Potentiometer of variable resistance of 10k which can be used on an experimental board, but it can also be installed in the housing. They can be used for various types of control, eg. Setting how the brightness of LEDs.
A 100k variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.
A 500k variable resistance potentiometer that fits the experimental board, but can also be built into the housing due to its increasing size. They can be used for various types of control, eg adjusting how bright the LED is.
A 1M variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.
Caps for THT potentiometer from our store that would make control much easier and would simply just look better.
Potentiometer with mutable resistance from 10k that corresponds with the breadboard. They can be used for various kinds of control, for example adjusting the intensity of LED lights. One of these is also in our Dasduino Beginner Kit.
RV24YN20S Potentiometer with variable resistance of 10k intended for housing installation. Comes with cap and dial. Carbon, usually used to adjust the speed of rotation of the motor on the inverter.
Large pushbutton will often be more practical than the small one (classic pushbutton). With dimensions of 12mm x 12mm it can be pushed in the breadboard, but it is also suitable for ordinary drill boards.
SPST (single-pole, single-throw) is a simple switch that connects or disconnects the two contacts in its casing.
• Type: SPST
• Shape: box
• Max. current/voltage: 250VAC 10A
• Dimensions: 17mm x 13mm x 11mm (without contacts)
SPST (single-pole, single-throw) is a simple switch that connects or disconnects the two contacts in its casing.
• Type: SPST
• Shape: elongated
• Max. current/voltage: 250VAC 10A
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This built-in switch comes in a metal case and comes with backlighting in various colors. In addition, this switch is waterproof, shockproof and vandal-proof.
This interesting product enables you to control who has is allowed to turn on or turn off a circuit. Namely, in order to change the status of this switch, you need to put the key in the lock and turn it around.
Large DPDT (Dual Pole Dual Throw) panel mount switch. Breaks two wires simultaneously.
These magnetic door switch sensors are already seen, if not – then in old movies for sure where they were used as anti-theft devices, ie. alarm systems. In fact, it is a magnet and the reed switch inside a pair. When they are close to each other (recommended 13mm or less), reed switch closes. Connect it to Croduino / Arduino as an ordinary switch use the detection of open doors, windows, drawers, cupboards etc.
• Voltage: max. 200V, best used 5V Croduino/Arduino
• Max reed power: 100mA
• Max detection distance: 15mm, 13mm recommended
• Dimensions: 29 x 14 x 9mm
• Cable length: 30cm
Reed switch is a switch that is activated within the range of the magnetic field. Within its glass capsule, it has two metal wires that will move when they are near the magnet and thus “activate” switch.
SPDT (single-pole, dual-throw) is a simple switch that connects the centre contact to one of the other two contacts located on its housing.
The DIP switch is a small switch that is simply used with breadboard or protoboard.
• Number of poles: 2
• Pitch: (2.54mm)